A cover plated beam consist of a W21 x 62 with 12mm x 300mm plates attached to the top and bottom of the flange and is fastened by two rows of 20mm diameter rivets. The beam has a simple span of 5.0m and carries a uniform load of 250KN/m. For W- Section d = 560mm 1= 1510 x10° mm Determine the longitudinal spacing or pitch of rivets if the allowable shearing stress ion rivets is Fv = 100 MPa.

A cover plated beam consist of a W21 x 62 with 12mm x 300mm plates attached to the top and bottom of the flange and is fastened by two rows of 20mm diameter rivets. The beam has a simple span of 5.0m and carries a uniform load of 250KN/m. For W- Section d = 560mm 1= 1510 x10° mm Determine the longitudinal spacing or pitch of rivets if the allowable shearing stress ion rivets is Fv = 100 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 Determine the design angle 8 for connecting mem- ber A to the plate if the resultant force is to be directed vertically upward. Also, what is the magnitude of the re- sultant? F₁ = 500 N -00 00 y ooo B FB = 400 N X
2. Determine the adequacy of the clip angle connection shown. The allowable stresses are 100 MPa for shearing, 220 MPa for bearing, and 140 MPa for tension for the seat angle and the rivets. 45 kN 220 mm I 16 65 32 150 150x100x16 clip angle 20 mm o rivets 16 100
6. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24mmp A490N bolts. The plate is A36. Determine the safe load Pu using LRFD that the truss can resist according to the capacity of the connection. 15 15 с 1.5 3P. + D 1.5 80 mm 70 mm 70 mm 80 mm Fac 7. Repeat Problem 6 using 30mm A325-N bolts and A-50 steel. Use ASD. 50 mm Fac
10/... find the shear stress in bolts 5 1) 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 110 MPa. 127 MPa. 509 MPa no one O 300 mm 8 mm
8. H / The beam shown below has across seclion of channel Shape with width 360mm.and haghs h= loomm, the web thickness ist= 14mm.Deler- Mine ihe Max imum tensile aud Compressive stressin the beam due to unifom Load? 360Mm 3.6KN/M 14m tiom Please Sir 5T CASIC f-991ES PL DATURAL u CALC (-)
Test#1 -zzen-zax AlpQLSdM75VMOVqbMa1WtS9n99RYc6PifeGUTpVBOluyMUUVYQgqqA/formResponse YouTube Replace the three forces which act on the bent bar by a force-couple system at *.the support point A 2100 lb 4' 1500 lb •A B. 30° C. 2' •E. 800 lb 3' oogle
REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Peso 100 m
M3 HW 4 4. Six rivets are used in the connection shown in the REVISED PROBLEM: figure. If both P= 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Pe so 100 mm
A steel beam having a span of 14 m. carries a dead load concentrated load Pp = 60 kN at its midspan. The beam is laterally supported at its span. Properties of the wide flange section. rts - 104.39 mm ho - 338.08 mm Jo -1.69 x 10^6 Cw - 4.3 x 10^12 d=356.11 mm tf = 18.03 mm tw - 11.18 mm Sx - 2343 x 103 mm rx = 155.96 mm ry - 93.98 mm Sy = 818 x 10^3 mm Zx = 2573 x 10^3 mm Zy= 1239 x 10^3 mm Fy = 345 MPa Iy = 151 x 10 mm Lp=3.98 Lb=14m Lr=12.98 Cb=1.14 Determine the safe concentrated live load that the beam could support at the center based on its design strength
Problem 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing stress due to rivets is 140 Mpa • Thickness of the member is 5 mm • Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 N 120 N 200 N 4 Pands 4m - 16 m
*7-32.d The double T-beam is fabricated by welding the three plates together as shown. Determine the shear stress in the weld necessary to support a shear force of V 80 kN. 20 mm 150 mm TION 50 mm 75 mm 50 mm 20 mm 20 mm Probs. 7-32/33 anscribed image text
0O REDMI NOTE 8 PRO O AI QUAD CAMERA Q - 4. For the given truss structure below; BY USING THE METHOD of SECTIONS; determine the internal forces of the elements BD, CD & CE. Also determine whether these forces are TENSILE or COMPRESSIVE. 3 in 3 m -4 m -4 m -4 m- 1.75 kN 2KN 1.5 kN 2kN I kN 9.75 kN G 6 m 6 m 6m 6 m