A copper cylinder 4in. inside diameter has walls 1in. thick. End plates are stayed by a 1in. diameter bar of steel which passes through the cylinder and is just tight at 12°F. Estimate the stress in cylinder and stay when steam at atmospheric atmosphere (212°F) is admitted. Assume the end plates do not deform. Use the following values: ac = 0.00001/°F Ec = 15,700 ksi as = 0.0000062/°F Es = 29,000 ksi

A copper cylinder 4in. inside diameter has walls 1in. thick. End plates are stayed by a 1in. diameter bar of steel which passes through the cylinder and is just tight at 12°F. Estimate the stress in cylinder and stay when steam at atmospheric atmosphere (212°F) is admitted. Assume the end plates do not deform. Use the following values: ac = 0.00001/°F Ec = 15,700 ksi as = 0.0000062/°F Es = 29,000 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Chapter 5, Reserve Problem 026 A solid aluminum [E = 70 GPa; a = 22.5 x 106/°C] rod (1) is connected to a solid bronze [E = 100 GPa; a = 16.9 x 106joc] rod (2)vat flange B as shown. Aluminum rod (1) has an outside diameter of 58 mm, and bronze rod (2) has an outside diameter of 110 mm. The bars are unstressed when the structure is assembled at 30°C. After the 300-kN load is applied to flange B, the temperature increases to 45°C. Determine the normal force in rod (1). 150 kN (2) (1) 150 kN 2.6 m O 40.1kN (C) O 62.2kN (C) O 54.0kN (C) O 49.0kN (C) O 74.3kN (C)
View Policies Current Attempt in Progress A solid aluminum [E = 70 GPa; a = 22.5 x 10-6/°C] rod (1) is connected to a solid bronze [E = 100 GPa; a = 16.9 x 10-6/°C] rod (2)vat flange B as shown. Aluminum rod (1) has an outside diameter of 50 mm, and bronze rod (2) has an outside diameter of 122 mm. The bars are unstressed when the structure is assembled at 30°C. After the 300-kN load is applied to flange B, the temperature increases to 45°C. Determine the normal force in rod (1). 150 kN B (2) (1) 150 kN 2,6 m 1 m O 48.4 kN (C) O 60.4 kN (C) O 44.2 kN (C) O 31.9 kN (C) O 35.4 kN (C)
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
X Ø ER F Ⓒ Priv Terr ing Time: 2 hours, 23 minutes, 08 * Question Completion Status: 87°F Cloudy 3 Tensile Force, P = 294 KN Pipe Dimensions: Outer Diameter = 84 mm Inner Diameter = 70 mm Length, L = 339 mm Material Property. Esteel = 200 GPa Ealuminum = 70 GPa A P= Beconds. The A-36 steel pipe has a 6061-T6 aluminum core. It is subjected to a tensile force. Given: O 10 L 11 12 14 Determine the average normal stress (MPa) in the aluminum due to this loading. Express your answer in 2 decimal places. 15 - P 16 17 18 19 20 ho W 6
For the frane shown below use unite load melhed to defermih ventical defketion at C2 E=200 kN I = 300 Cm lom 20kN hinge the a 9. 5m
24 Tensile test well done with standard tensile test spaceman with diameter 25 mm & length 120 mm the table in the attachment picture shows the applied load in KN and the elongation in mm. the yield stress is Load 37.5 75 75 85 110 120 125 115 (KN) Elongation (mm) 100 0.06 0.12 1.4 4 12 18 24 29 32 O 320mm2 O 325mm2 O 239mm2 O None of the above
Q-2 The rotating shaft running at n = 900 rpm, shown in the figure below, is machined from AISI 1045 CD steel. It is subjected to a force of F = 10.1 kN. The shaft is experiencing an operating temperature of 35 oC. With the specified loading and for a reliability of 99.9 %, a) Determine the minimum factor of safety for fatigue based on infinite life*. b) Determine the maximum safe load (Fmax) that can be applied for a factor of safety of 1.5 and a design life of 5x105 cycles, all other input values remaining the same. c) Determine factor of safety against yielding. *Free-body, shear-force and bending moment diagrams are required.
a. Determinc_ the Force g AC bDetermine the torde f AB | 2' 8'
Quiz-3: (Optional) Find the stresses which may induced in each rod if temperature is increases by 70°C. Aluminum Bronze 1.2m 6mm, Im AA-20 Cm² Ав15 Сm? ɑAi-23*106 m/m.°C ɑB=18*10-6 m/m.°C EA-70GPA Ев 80GPa
(47 H.WOA rod Consists of three bars of unegqual dlameters as shown in fig., find the Stress in each bar and the C longation of the rocd ? use E= 200G Va Ø= 4omm Ø=20 mm 2. W 1.5m 2.5m 2m مرّ للأعلى لاستعراض الفلاتر II V
A pipe carrying steam at 3.5 MPa has an outside diameter of 450-mm and a wall thickness of 10-mm. A gasket is insertedbetween the flange at one end of the pipe and a flat plateused to cap the end. How many 40-mm diameter bolts must beused to hold the cap on if the allowable stress in the bolts is 80 MPa of which 55 MPa is the initial stress. Whatcircumferential stress is developed in the pipe?
47 H.WOA rod Consists of three bars af unequal dlameters as shown in fig., find the Stress in each bar and the C longation of the rood ?_use E= 200GPA %3D =30mm =20 mm 1.5m 2.5m 2m