A composite beam consists of a nforced with a materi 2 strip bonded to the bottom surface as shown. Material 1 has elastic modulus E₁ = 78 GPa and material 2 has elastic modulus E2 212 GPa. If the beam is bent around a horizontal axis with moment M = 56 kN. m, determine the maximum normal stress in each of the materials. CORE (Material 1) COVER PLATE (Material 2) ( L₁

A composite beam consists of a nforced with a materi 2 strip bonded to the bottom surface as shown. Material 1 has elastic modulus E₁ = 78 GPa and material 2 has elastic modulus E2 212 GPa. If the beam is bent around a horizontal axis with moment M = 56 kN. m, determine the maximum normal stress in each of the materials. CORE (Material 1) COVER PLATE (Material 2) ( L₁

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.5.6P: The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of...

See similar textbooks

Similar questions

Q3: The wooden section of the beam is reinforced with two steel plates as shown. If the beam is subjected to a moment of M = 5.0 kN. m, determine the maximum bending 20 mm 300 mm stresses in the steel and wood. Sketch the M = 5 kN-m stress distribution over the cross section. Take 20 mm Ew = 11 GPa and Est = 200 GPa 200 mm
LA steel wire of 20 mm diameter is bent into a circular shape of 10 m radius. If E, the modulus of elasticity is 2 x 106 kg/cm2, then maximum stress induced in the wire is
The beam shown is subjected to compressive force of C1/2 kN.m, and bending moment of C2 N.m, calculate the total stresses on both points A and B* Sigma A = Sigma B = C2=140 C1=90 Во 40mm 20mm
The lever must exert a force of P = 3800 Ibs at B as shown. The lever lengths are a = 11 in. and b = 47 in. The allowable bending stress for the lever is 12600 psi. If the lever height h is to be 3.5 times the lever thickness t (i.e., h/t = 3.5), what is the minimum thickness t that can be used for the lever? h Cross section Lever a Answer: t = i in.
As shown in the figure below, determine the internal loadings at points D and. Consider the weight of the beamwhich is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is sallow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stressconcentration at the notch.
A box is produced by joining the wooden and plywood rectangular elements with screws as shown in the section. The shear force that each screw used in the cross section joint can safely carry is V = 2 kN. If the beam element created in this way is loaded from the middle of the span with a load of P = 100 kN, find the screw gap a and the total number of screws to be used in the beam element. (Cross-section dimensions t = 15mm, b = 150mm, c = 30mm, h = 180mm; beam support span L = 5m)
Q1/ A composite beam is made of wood and reinforced with steel strap located on its bottom side. It has the cross-sectional area shown in fig. if the beam is subjected to a bending moment of M=2kN.m, determine the normal stress at wood and steel. Take Ew=12Gpa and Est=200Gpa. 150mm Wood en 20mm Steel 150mm
A beam section has the z-axis and y-axis as the principal centroidal axes and I₂ = 15 x 106 mm and I, = 8 x 10 mm. The beam carries a moment with components M₂ = 5 kN.m and M₁ = -4 kN.m. What is the stress at the location z = 35 mm and y = 60 mm within the beam section? Show your work Select one: a. -2.5 MPa b. 2.5 MPa c. Od. 37.5 MPa -37.5 MPa
5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E-200 GPa and BD from aluminum with E-70 GPa. The diameters of posts AC and 80 are 25 mm and 40 mm, respectively. Determine the vertical displacement of point on AB 100 KN 400mm D 6. The timber beam has a cross-sectional area of 2000 mm and its modulus of elasticity is 12 GP Axial loads are applied at points B, C, and D as shown. Calculate the total change in length of the beam. Answer: 2.33 mm 40 KN 35 KN 20 KN 3.20 m 1.60m 3.20 m
A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E= 200 GPa. The bending is about the z axis. A couple of moment equal to the full plastic moment Mp is applied and then removed. Using a yield strength of 236 MPa, determine the residual stress at y = 45 mm. 15 mm C 30 mm The residual stress is 30 mm 30 mm 30 mm 15 mm MPa.
AT-shape beam is a load-bearing structure. The top of the T-shape cross section serves as a flange or compression member in resisting compressive stresses. In a building construction, the T-Shape beam which made of an elastic perfectly plastic material was used and its dimension is shown in Figure 3.2. For the beam indicated, determine the fully plastic moment and shape factor of the beam if the value of E = 200 GPa and o, = 250 MPa. (Use moment inertia for the cross section, I = 2600 x 10° m*) 60 mm 20 mm 60 mm 20 mm Figure 3.2 Beam cross-section