A coal fired thermal power station and a nuclear power station have the following data: Coal Nuclear Capital cost (S/KW) 700 800 Annual Interest and depreciation 10% 10% 0.153 Running cost per unit ($ / kWh) Annual load factor 0.341 50% 60% On the basis of 1kW output on annual basis Use the above information to answer Q22 - Q26 22. Calculate the annual capital cost of the coal fired thermal power station a) $0.700 b) $7.00 c) $70.00 d) $700.00 e) none 23. Calculate the annual capital cost of the Nuclear power station a) $0.800 b) $8.00 c) $80.00 d) $800.00 none 24. Calculate the energy generated per annual for the Nuclear power station a) 4900 kWh b) 5250 kWh c) 6789 kWh d)7590 kWh e) none

A coal fired thermal power station and a nuclear power station have the following data: Coal Nuclear Capital cost (S/KW) 700 800 Annual Interest and depreciation 10% 10% 0.153 Running cost per unit ($ / kWh) Annual load factor 0.341 50% 60% On the basis of 1kW output on annual basis Use the above information to answer Q22 - Q26 22. Calculate the annual capital cost of the coal fired thermal power station a) $0.700 b) $7.00 c) $70.00 d) $700.00 e) none 23. Calculate the annual capital cost of the Nuclear power station a) $0.800 b) $8.00 c) $80.00 d) $800.00 none 24. Calculate the energy generated per annual for the Nuclear power station a) 4900 kWh b) 5250 kWh c) 6789 kWh d)7590 kWh e) none

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
Disuss the operation of several different types of generation plants (i.e., steam, nuclear, wind, etc.)
a. Explain about Energy crisis.
In a PWM, how do we calculate duty cycle?
b) A1000 MW turbine generated 648 MWh during 30 day. What would is capacity factor be?
Draw the circuit diagram of Two quadrant chopper which is having average load voltage might be positive or negative. Explain each quadrant operation with neat sketch. I want more than 350 words and I do not want it in handwriting
Load on a small power station is as under. Draw the load curve and calculate 1. Maximum demand 2. Units generated in a day 3. Average demand 4. Daily load factor.
1MV ll zain IQ First Quiz.pdf -> First Quiz A generating station has a maximum demand of 10 MW. Calculate the cost per unit generated from the following data: Annual load factor = 35% Capital cost = Rs 12,50.000 Annual cost of fuel and oil = Rs 8.00.000 Taxes, wages and salaries = Rs 7,00,000 Interest and depreciation = 10%
critically explain difference between short and long run energy demand.
Advantages of using per unit system in power system studies is O a. None of these O b. Both more informative and calculations are easy. O c. More informative O d. Calculations are easy
Two 60MVA, alternators operate in parallel. The setting of the governor are such that the rise in speed from full load to no load is 2% in one machine and 3% in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 120MW, what will be the load on the first machine (with 2% speed regulation) when the total load is reduced to 80MW?
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.