A civilian aircraft is flying at a Mach number of 0.8 at an altitude where the ambient pressure and temperature are 26.5 kPa and 223 K, respectively. The aircraft is equipped with two simple turbojet engines. The stagnation temperature at the entrance to their nozzles is 1200K and remains unchanged. You may assume the nozzles are operating under ideal conditions and the properties of hot gases leaving the nozzles are the same as air. 1- Under certain operating conditions each engine produces a gross thrust of 50x10³ N with an exit velocity of 600 m/s. For each nozzle determine its mass flow rate, exit area and the corresponding stagnation pressure at its entrance. 2- For a fuel to air ratio of 0.02, determine the net thrust of each engine corresponding to the above (part 1) operating condition. 3- What should be the minimum supply pressure to the nozzles if they were operating at choked condition? Then determine the gross thrust of each nozzle. 4- Show that for a choked convergent nozzle further reduction in the throat area has no effects on the exit Mach number. Use sketches to illustrate your answer.

A civilian aircraft is flying at a Mach number of 0.8 at an altitude where the ambient pressure and temperature are 26.5 kPa and 223 K, respectively. The aircraft is equipped with two simple turbojet engines. The stagnation temperature at the entrance to their nozzles is 1200K and remains unchanged. You may assume the nozzles are operating under ideal conditions and the properties of hot gases leaving the nozzles are the same as air. 1- Under certain operating conditions each engine produces a gross thrust of 50x10³ N with an exit velocity of 600 m/s. For each nozzle determine its mass flow rate, exit area and the corresponding stagnation pressure at its entrance. 2- For a fuel to air ratio of 0.02, determine the net thrust of each engine corresponding to the above (part 1) operating condition. 3- What should be the minimum supply pressure to the nozzles if they were operating at choked condition? Then determine the gross thrust of each nozzle. 4- Show that for a choked convergent nozzle further reduction in the throat area has no effects on the exit Mach number. Use sketches to illustrate your answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question Four Air flows steadily adiabatically through a pipe with a cross-sectional of 0.002 m?. At the inlet of the duct, the pressure and temperature are 100 kPa and 50°C, respectively. At the exit of the duct, the temperature and velocity are 100°C and 600 m/s, respectively. Determine the Mach number and the velocity at the inlet section. Also, calculate the mass flow rate. Ans. M 1.884, vi = 678.7 m/s, m = 1.46 kg/s.
A converging-diverging nozzle is supplied with air from a reservoir where the pressure and temperature are 600 kN/m² and 18°C respectively. The throat area is 10 cm? and the nozzle is designed for a final Mach number of 2.0. The flow is isentropic and the air behaves as an ideal gas. Calculate: a) The exit plane area and the exit plane pressure at the given design condition. b) The pressure at the throat when the nozzle first chokes and the corresponding throat temperature. c) The density of the fluid in the reservoir. d) The density of the fluid at the throat. e) The choking mass flow. f) The maximum exit pressure for which the nozzle remains choked.
multi-stage high –pressure steam turbine is supplied with steam at a stagnation pressure of 7 MPa and a stagnation temperature of 5000C. The corresponding specific enthalpy is 3410kJ.kg. The steam exhaust from the turbine at a stagnation pressure of 0.7 MPa abs., the steam having been in a super-heated condition throughout the expansion. It can be assumed that the steam behaves like a perfect gas over the range of the expansion and that ᵞ = 1.3. Given that the turbine flow process has a small-stage efficiency of 0.82, determine (1) the temperature and specific volume at the end of the expansion; (2) the re-heat factor. The specific volume of superheated steam is represented by pv=0.231(h-1943), where “p” is in kPa, v is in m3/kg and “h” is in kJ/kg.
1. Air flow isentropically through a converging nozzle attached to a reservoir, where the pressure is 170 kPa and temperature is 300 K. At the inlet to the nozzle the Mach number is 0.2, the nozzle discharge to the atmosphere (100kPa). The discharge area is 0.02 m?. Determine the magnitude and direction of the force that must be applied to hold the nozzle in place.
i just need final answer The tank is filled with air at 20°C and 139 kPa in stationary condition. Air is leaving the tank with flowing in anozzle under steady-state condition. The flow is under isentropic and subsonic condition. The nozzle exit area is28,1 cm2. After leaving from the nozzle, air strikes a vertical plate. Define the force [N] required to hold the platestationary. (Note: Assume Pe=1 atm, kor=1.4, Ric=287 J/kg.K)
What would happen if we tried to further accelerate a supersonic fluid with a diverging diffuser?
The stopping pressure of the air flow at the inlet of a pipe with an inner diameter of 20 cm is 1.1 atm, the static pressure It is 1 atm and its temperature is 285°K, and the Mach number at its exit is 0.6. Average friction inside the pipe Since the coefficient is 0.005, the length of the pipe, the stopping pressure at the outlet, the static pressure and the Calculate the temperature.
stagi 900 kPa 1- Air enters a compressor for a mass flow rate of 0.04 kg/s. at a stagnation temperature 358 K. Assuming the AIR compression process to be isentropic, determine the power 0.04 kg/s require. 100 kPa stagnation
An ideal gas is to flow isentropically from a large tank where the air is maintained at a temperature and pressure of 59 °F and 76 psia to standard atmospheric discharge conditions in a way to achieve a maximal velocity. Describe in general terms the kind of duct involved and determine the duct exit Mach number and velocity in ft/s if the gas is air. The problem can be solved either using the isentropic relations or this figure. The isentropic relations are more accurate, but difficult to use unless you code them into a computer program. (a) What is the pressure ratio for the flow? (b) Is the exit flow subsonic, sonic, or supersonic? (c) What is the exit Mach number? (a) Pexit/Po= i (b) (c) Mexit =
1. Air is flowing isentropically through a converging duct which is fed from a large reservoir where the temperature and pressure are 350 K and 250 КРа, respectively. At a certain point along the duct, where the cross-sectional area is 0.005 m, Determine the Mach number, temperature the pressure is 150 kPa. and velocity at that point and also calculate the mass flow rate. (Ans: 330.1 K, 0.549, 162.8 kPa, 1.718 kg-s). 2. Air is supplied to a converging nozzle from a large reservoir where the temperature and pressure are 400 K and 100 kPa, respectively. At a certain cross-section, the temperature and pressure are measured to be 383.8 K and 63 kPa, respectively. Assuming isentropic flow, find the Mach number at this cross- section and the mass flow rate per unit area. (Ans: 0.46, 103.3 kg-s1-m?). 3. A converging nozzle is fed with air from a large reservoir where the temperature and pressure are 400 K and 170 kPa, respectively. The nozzle has an exit cross-sectional area of 0.001 m? and…
Air flows through a long, isentropic nozzle. The temp. and pressure at the reservoir are 1000 K and 20 atm respectively. If the Mach number at the entrance is 0.2, what is the gas velocity at the entrance
Q1) Air is to be expanded to Mach number (2.0) in a convergent-divergent nozzle from an inlet velocity of (100 m/s). The inlet area is (50cm³). Inlet static temperature is (500K) and static pressure is 101.3 kpa. Assuming isentropic flow determine: 1. The Mach number at the inlet. 2. The stagnation pressure and temperature. 3. The temperature and pressure at the throat. 4. The velocity and temperature at exit. 5. The throat and exit temperature. 6. The mass flow rate.