A Carnot vapor refrigeration cycle operates between thermal reservoirs at 7°C and 28°C. The working fluid is saturated vapor at the end of the compression process and saturated liquid at the beginning of the expansion process. Determine the operating pressures in the condenser and evaporator, in bar, and the coefficient of performance for each of the following as the working fluid.

A Carnot vapor refrigeration cycle operates between thermal reservoirs at 7°C and 28°C. The working fluid is saturated vapor at the end of the compression process and saturated liquid at the beginning of the expansion process. Determine the operating pressures in the condenser and evaporator, in bar, and the coefficient of performance for each of the following as the working fluid.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter7: Thermal Processes

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

A full scale agitation system that has a flat blade turbine impeller with six blade-disk is used in a mixing operation. The (Da/W) and (D/J) values are 5 and 12, respectively. The liquid level is equal to the tank diameter. The liquid in the agitator has a viscosity of 85 cp and a density of 65.5 lb/ft³. The Reynolds number for the agitator is 10,000 and the agitator requires a power of 1 kW. It is desired to scale down the system for a vessel whose production volume is 4 times smaller than the original full scale agitation system. Assume mass transfer similarity for the scale down process. Calculate the power requirement in kW for the scaled down tank. Problem 2. 4
4. An ideal vapor-compression heat pump cycle with Refrigerant 134a as the working fluid provides 15 kw to maintain a building at 200°C when the outside temperature is 50°C. Saturated vapor at 2.4 bar leaves the evaporator, and saturated liquid at 8 bar leaves the condenser. Calculate (a) The power input to the compressor, in kW (b) The coefficient of performance. (c) The coefficient of performance of a reversible heat pump cycle operating between thermal reservoirs at 20 and 50°C. (h, = 244.09kJ/kg, s, = 0.9222 kl/kg – K; h2 = 268.97 kJ/ kg; h, = 93.42 kJ/ kg) %3D
A 1.5-ft³rigid tank contains saturated refrigerant-134 at 170 psia. Initially, 20 percent of the volume is occupied by liquid and the rest by vapor. A valve at the top of the tank is now opened, and vapor is allowed to escape slowly from the tank. Heat is transferred to the refrigerant such that the pressure inside the tank remains constant. The valve is closed when the last drop of liquid in the tank is vaporized. Determine the total heat transfer for this process. R-134a, Sat. mixture P = 170 psia V = 1.5 ft³
Which of the following is not true for the pan coefficient applied to Class A pan? (i) it is always less than 1.0 (ii) it adjusts evaporation rates for stored heat from sides and bottom (iii) all of the above is true
For distilled water the conductivity is zero. Why?Enlist apparatuses used in titration method.
3: Ammonia gas(A) and nitrogen gas (B) are through a straight glass tube 2-0 ft long with an inside diameter 24.4mm at 298 K and lol.32 Kla. Both ends of the fube are Connected to large mixed chambers at lol.32 k Pa. The Partial pressure of NH3 is constant at 20 kPa in one cham ber and 6.66 KPe in the offer. @ Calculate the diffusion of NHs @ Calculate the diffusion of N2 O Calaulate the partial presures at pomt (o.305 m) it the fube dffusing in GunterdBhe
Acceleratory period begin after 6 hours of * hydration True O False O . Matter is de fined as إجابتك Felite is .. إجابتك
concentration of (1.5 mg/liter). 3- The pump of waste water of concentration (1.5 mg/liter) treatment plant system is powered by a (15 kw) electric motor whose efficiency is (90%). The water flow rate of the pump is (50 L/sec).The diameter of the inlet and outlet pipes are the same, and the elevation difference across the pump is negligible. If the pressure at the inlet and outlet of the pump are measured to be (100 Kpa) and (300 kpa) absolute, respectively. Determine the mechanical efficiency of the pump. 19 (41:13
True/False questions. 1 For filtration process: when the water level rises to the point that the filter bed must be cleaned. This point is called terminal head loss ( 2 As the temperature decreases the detention time in 7 slow-mix tank decreases. ( 6 8 When CO₂ is bubbled in water with carbonate buffer system, the pH will decrease slightly and the reaction will shift to the left. ( ) 9 The lower the water turbidity, the higher the allowable ) scour velocity in sedimentation tank.( For mixed-media filter the layer of garnet is used to catch the very fine particles ( 3 The addition of polymers in coagulation process is called inter-particle bridging. ( ) ) 4 Slow-mixing can be accomplished by hydraulic As the weir lengths become shorter the scouring velocity becomes higher ( jump ( ) ) 5 Water with high turbidity requires more coagulant 10 Aluminum sulfate has a wider pH range for effective to be treated. ( coagulation than fèrric salts ( )
An absorption column is to be designed to recover 99.5% of the NH3 from a feed stream, which is supplied at 72 oF and an NH3 partial pressure of 10 mm Hg.
4- Rapid-mixing can be accomplished by several ways, mention 3 of them.
lysimeter is used to measure infiltration В evaporation (c) evapotranspiration vapor pressure