A cantilever beam made of wood spans L- 6 ft. The beam has a rectangular cross section with a width w - 8 in. and a depth d - 20 in. The moment of inertia of the cross section about the horizontal centroidal axis is 5333 in. . A concentrated load Pwill be applied to the free end of the cantilever beam. Calculate the maximum magnitude that may be permitted for concentrated load Pif the allowable shearing stress for the wood is 100 psi. Answer: Ib Save for Later Attempts: 0 of 1 used Submit Answer

A cantilever beam made of wood spans L- 6 ft. The beam has a rectangular cross section with a width w - 8 in. and a depth d - 20 in. The moment of inertia of the cross section about the horizontal centroidal axis is 5333 in. . A concentrated load Pwill be applied to the free end of the cantilever beam. Calculate the maximum magnitude that may be permitted for concentrated load Pif the allowable shearing stress for the wood is 100 psi. Answer: Ib Save for Later Attempts: 0 of 1 used Submit Answer

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

a.) Compute the maximum bending moment of this beamb) The base of the beam is 200mm and the allowable flexural stress of the beam is 70 MPa, design the depth of the beam.
From the given figure below, determine the maximum flexural stress of the beam if it has a cross section of 150mm wide by 250mm deep. (JN 10 N/m o' RA=42N 42N 3M B IM 75Nm 81NM Im RD=3N -3N 0° 78 Nm 3NM V-DIAG M-DIAG
Compute the maximum flexure stresses for the beam loaded shown 15 KN/m 2m 150 mm 250 mm w=6KN/m 3m 1m B
Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 75 mm 75 mm Empedopre|72 -75 mm 150 mm 50 mm EN SAMA 00 kN B 1.0 m 60 kN -1.5 m-> rode D 1.0 m
Q2: A cantilever beam AB, loaded by a uniform load and a concentrated load, is constructed of a channel section. Find the maximum tensile stress g and maximum compressive stress gc. 15 N 20 N/m 40 mm 40 mm F 225 mm- 40 mm 200 mm 2.5m 0.5 m
C):-The rigid bar BDE is welded at point B to the rolled-steel beam AC. For the loading shown, determine (a) The slope at point 4. (b) The deflection at point B. Use E 200 OP 20 kN/m AT 24*2 s mid-1.5ml-1.5 m
The simply supported beam consists of a W21x 44 structural steel wide-flange shape [E = 29,000 ksi: 1-843 in.). Assume that the support at D can provide resistance either up or down. For a loading of w-6.7 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB 12 ft. Lac-5 ft. Lcp-5 ft. Loe * 4 ft. Answers: LAB (a) VA (b) vc i i B Lac LCD in. D in. LDE E
1. For the given loaded beam shown, a. b. C. d. 40 kN-m B Im Im C 12 kN/m 3 m 2m E 125 -15- 15 145 Sketch the shear and moment diagram. Determine the maximum tensile bending stress in the beam. Ans. Determine the maximum compressive bending stress in the beam. Ans. Determine the maximum horizontal/transverse shear stress in the beam. Ans. dire lengt
No. 3. Beam AC carries a concentrated load P at its midspan point B. Determine the depth of the beam h in mm if the maximum bending stress is Omax = 50 MPa, the maximum deflection 8max = 10mm, the span is L = 4m, and the modulus of elasticity is E = 200 GPa. L/2 L/2- B 4+ 18. max
Question The span of cantilever beam is 2 m. The cross-section of the beam is a hollow square with external sides 100 mm; and its I = 4 x 105 mm4. The safe bending stress for the beam material is 100N/mm². The safe concentrated load at the free end would be
The cantilever beam (of type w8 × 15) made of A36 steel alloy has a depth d = 8.11 in, as shown below. The moment of inertia I, is 48.0 in.“. 1, 400 lb |1, 400 lb 100 lb/ft d -5 ft- -5 ft- (a) Determine the maximum internal bending moment produced by the loading con- dition provided. (b) Determine the maximum normal stress, due to the bending mo- ment, and the corresponding factor of safety (using o y as the failure stress). (c) Draw a graph that shows the stress in the beam along the y-direction at the point chosen in part (a). (d) Calculate emax based on your answer to part (b). (e) Calculate the radius of curvature p based on your answer to part (d). (a) 26 kip-ft (you should find reaction force of 3.8 kip); (b) 26.4 ksi, 1.38; (c) o(y) = 6.5 у ksi; (d) 9.10(10 4); (е) 372 ft
A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of 36mm diameter bars Compute For: 1.) The depth of the concrete stress block is Blank 1 mm. 2.) The magnitude of the nominal moment capacity is Blank 1 kN.m