A beam having a simple span of 6.38 m. carries a uniformly distributed load as follows. Service dead load (including its own weight = 31.98 %3D kN/m). Use LRFD. Properties of W 21 x 57 A = 10,774 mm2 %3D d = 534.92 mm tw = 10.29 mm %3D Sx = 1819 x 10³ mm3 %3D Zx = 2114 x 10³ mm³ %3D k = 34.93 mm %3D bf = 166.50 mm %3D tf = 16.51 mm %3D Fy = 345 MPa %3D E = 200,000 MPa %3D Determine the uniform live load it could support based on the design shear strength. (kN)

A beam having a simple span of 6.38 m. carries a uniformly distributed load as follows. Service dead load (including its own weight = 31.98 %3D kN/m). Use LRFD. Properties of W 21 x 57 A = 10,774 mm2 %3D d = 534.92 mm tw = 10.29 mm %3D Sx = 1819 x 10³ mm3 %3D Zx = 2114 x 10³ mm³ %3D k = 34.93 mm %3D bf = 166.50 mm %3D tf = 16.51 mm %3D Fy = 345 MPa %3D E = 200,000 MPa %3D Determine the uniform live load it could support based on the design shear strength. (kN)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?
Find the maximum P,? P= ? (including beam weight) P= ? fe = 5,000psi fy = 60,000psi Wp = 3 k/ft = 5 k/ft 15" 42" 4#10 bars ↑3 4#10 bars 8 ft 8 ft 8 ft 24 ft 00
2. Like 20 ft 3 KLF K 12000 Mmax= A max= 932 2adbl
What will be the safe weight per linear meter length of the beams if the displacement at E is limited at 8mm. Where x=14.37m. = Properties of Steel: Ast 300mm², Est-200 GPa, Lst=2m = Properties of Steel: Aal 500mm², Eal-70 GPa, Lal=2m 0:5X Whit ALUMINUM x STEEL с
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.
A built up section shown consists of A992 steel made from plates fully welded together. The flanges consist of PL16×380 and PL12×500 for the web. Fy = 345 mPa. Which of the following best gives the value of the section modulus? PL16x380 O 935x10^6 mm^4 3,514x10^3 mm^3 O 550x10^3 mm^3 O 3,887x10^3 mm^3 PL12x500
Situation 4: A W12x106 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb = 1.14 d = 328 mm bf = 310 mm tf = 25.1 mm tw = 15.5 mm kdes = 40.4 mm ry = 79.0 mm Ix = 388 x 10^6 mm^4 ly- 125 x 10^6 mm^4 Sx = 2380 x 10^3 mm^3 Zx=2690 x 10^3 mm^3 J-3800 x 10^3 mm^3 Cw=2870 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 16m? 565 KN-m 588 KN- m 521 KN-m 511 KN-m
The simply supported beam consists of a W460 × 82 structural steel wide-flange shape [E = 200 GPa; I = 370 × 10 mm“). For the loading shown, determine the beam deflection vc at point C. Assume P = 73 kN, w = 35 kN/m, LAB = LBC = 3.6 m, LCD = 1.7 m. %3D %3D %3D P. B. LAB LBC LeD Answer: Vc= 8.8767 mm.
L For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 17 kN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm tf = 20 mm tw = 15 mm %3D b tw O bending MPa Round to one decimal place
Steel Design Given: S = 2m L = 10m Superimposed dead load = 5 kPa Live load = 3.6 kPa Properties of Beam BFA section = W 460 x 97 kg/mArea (A) = 12320 mm^2Depth (d) = 465 mmFlange Width (bf) = 193 mmFlange Thickness (tf) = 19mmWeb Thickness (tw) = 11 mm Moment of InertiaIx = 445 x 10^6 mm^4Iy = 23 x 10^6 mm^4Yield Strength, Fy = 248 MPar (radius of gyration of a section compromising the compression flange plus 1/3 of the compression web area of compression flange = 50 mm. Consider bending about the x-axis. 1. The compression flanges are laterally supported only at midspan. With this condition, what is the permissible flexural stress if Cb = 1.0?
TEXT:A beam is made using structural timber C24. The beam is 6 meters long and fixedagainst displacement at node A and restrained against displacement in the vertical direction at node B,as indicated on the sketch. Modulus of elasticity of C24 is 0,7x105 N/mm2. The beam has cross-sectional data bxh = 73 x 198mm2. The beam is supported by a uniformly distributed load q= 4 kN/m between junction A and B. beams self-weight must be neglected in the calculations a) Calculate the bearing reactions of the beam for the given external load action.b) Establish a moment and shear diagram for the beam.c) Calculate the transverse displacement of node C.
For the given properties of beam below. Compute the flexural capacity of the beam. b = 390mm d = 440mm d' = 80mm fc' = 34.5MPA fy = 350MPA As = 4 - 40mm As' = 2 - 32mm A. USE NSCP 2001, Mu = kN-m B. USE NSCP 2015, Mu = kN-m