A battery pack of 30 nickel metal hydride battery modules powers a high performance electric vehicle. Each module has an open circuit voltage of 13 V and an effective resistance of 10 mohm for a 10 second acceleration pulse. What is the peak power capability of this battery pack using the USABC definition (peak power = 2/9 x Voc2/R where Voc is the open circuit voltage and R is the resistance) A. 75 kW B. 113 kW

A battery pack of 30 nickel metal hydride battery modules powers a high performance electric vehicle. Each module has an open circuit voltage of 13 V and an effective resistance of 10 mohm for a 10 second acceleration pulse. What is the peak power capability of this battery pack using the USABC definition (peak power = 2/9 x Voc2/R where Voc is the open circuit voltage and R is the resistance) A. 75 kW B. 113 kW

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

Find out the voltage supplied in a lithium-ion rechargeable battery and what electrochemical reaction it uses. Suggest why the electrochemical reaction of lithium-ion rechargeable battery is used in LED flashlights.
Which change to the circuit will not extend the charging time of one time constant.a. Increasing the value of the capacitorb. Increasing the value of the resistorc. Increasing the voltage from 15 to 20 volts
A PMMC instrument has internal resistance of 0.66 kn and gives full scale deflection for 30 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 57 V will be ohms. O 86333.64 O 189.34 O 1240.00 O -133.68
a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R = 1092, L=20 mH, and a = 60°. Determine: i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. Vs S₁ S4 Figure $3 $₂ Lo Vo
For the full wave rectifier circuit shown in Figure 2, calculate: 1) The maximum current thro ugh the load. 2) The average current through the load. Vrms = 280v Vin 3) The average voltage across the load. = 12K2 4) The rms value of the current. Vrms = 280v 5) The rectification efficiency. Figure 2
4. A 250 Ah rated lead acid battery with a 20 hour rated discharge time. If Peukert's constant n for this battery is 1.2, calculate the following: a. the rated battery discharge current b. The number of hours the battery will discharge if it is connected to a 25 A DC load. c. The battery capacity in Ah when it is discharged at 20 A.
sketch vL1 and vR2 on a graph. mark the labels in microseconds one time constant after the charging phase begins and the value of each voltage at that time
In the circuit of figure Nº A, the secondary voltage Vs is 15 volts rms with a frequency of 60 Hz, R equal to 100 Ohms and C equal to 1000 microfarads. The diodes are silicon (Vd = 0.7 volts) and the Zener diode is 15 volts. Determine:a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2
In the figure given we have u(t)=10· coswt [V]. We assume the diodesand the A-meter (A) to be ideal.a) Plot the waveform of the current flowing through the A-m in scale.b) What is the reading of the A-m, if it is moving-coil type?c) What is the reading of the A-m, if it is moving-iron type?d) Calculate the power factor of the WHOLE structure.
Q1.Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). 1. How much will the average and r.m.s voltage s be? 2. The r.m.s phase current and average load current Is=? & Idc=? 3. The secondary r.m.s voltage and transformer capacity Vs & KVA? 4. The inductances causes the voltage drop Lc=? 5. The diode forward current and maximum inverse voltage? 6. Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=.% ??
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance? If a full-wave rectifier is needed?