A 5º curve intersects a property line CD at point O. The back tangent intersects the property line at point C which is 105. 270 m. from the P.C. which is at station 2+040. The angle that the property line CD makes with the back tangent is 110° 50'. a.) Determine the distance CD. b.) Determine the stationing of point D. c.) Determine the deflection angle of point D from the P.C.

A 5º curve intersects a property line CD at point O. The back tangent intersects the property line at point C which is 105. 270 m. from the P.C. which is at station 2+040. The angle that the property line CD makes with the back tangent is 110° 50'. a.) Determine the distance CD. b.) Determine the stationing of point D. c.) Determine the deflection angle of point D from the P.C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1: The pipe has a mass of 36.7 kg/m and is fixed to the wall at A. Given F is 265 N and Q is 327.1 Nm. a) Determine the internal transverse force (z-direction) acting on the cross section at A. b) Determine the internal bending moment rotating about x-axis at the cross section plane at A. c) Determine the internal bending moment about the z-axis acting on the cross section at A. 2m S2 2m
2- Belonging to the beam given below a) Find the reaction forces on supports B and D. b) Draw the shear force and bending moment diagrams. c) Find the maximum bending stress occurring according to the given cross-sectional area and show which point it is. 12 kN 24 kN 50 mm 7 kN/m 100 mm A B E 90 kN-m 62.5 mm -3 m -6 m- -3 m- -3 m 50 mm 100 mm
Example1: Find the absolute max. moment. 10 4 3 1) 3m 12m
For the steel beam used to the support the loads shown below: a) Draw normal and shear force diagram and bending moment diagram. b) Determine the magnitude and location of maximum moment. w2=5KN/m w1=3KN/m F1=25KN F2=10KN "M2=20KNM M1 =20KNM (m) 2. 4. 8. 10. 12.
Determine the maximum shear force and bending moment in the simply supported beams shown below. a) The beam weight is 5kN considered as a distributed load over the beam length. Two bushwalkers with 850N weight each are standing 0.1m from either end of the beam/bridge. b) The beam weight is 5kN considered as a distributed load over the beam length. Two bushwalkers with 850N weight each are standing together at one end of the beam/bridge.
1) Derive the shear and bending moment diagram for the following beam loading: A 0000 500 N 500 N B 0.4 m- -0.4 m C D -0.4 m- 2400 N/m 0.3 m a) Using the method of cutting the beam at several points at distance x from A b) Using a method that uses the following relationships between V, w, and M: dv dx = -W V = E dM dx
PROBLEM 2: Part a.) Derive the appropriate equations for shear and bending moment throughout the beam. Measure x-distance from the left side of the beam and make sure to tell where each equation is applicable. Part b.) Draw the shear and bending moment diagrams for the beam. 3 kN/m A 6 m B 7 kN/m 3 m C
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b=8.0 ft, c=4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A A a B a B W Answers: Ay = i b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) W с b C C P C D P kips, Ey = d E i E X 'y x kips.
a) Determine the second moment of area (IXX) about the centroidal x-axis for the solid homogeneous beam section shown below, where the dimensions are b = 5.25 mm and d = 12.75 mm. Give your answer in mm4 to two decimal places. b) Determine the second moment of area (IYY) the about the centroidal y-axis for the solid homogeneous beam section shown below, where the dimensions are b = 5.25 mm and d = 12.75 mm. Give your answer in mm4 to two decimal places.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b-8.0 ft, c-4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A a a B Part 2 b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Save for Later B W Answers: Ay = i 37.575 eTextbook and Media W AV=P₂ b C V₁ - V₁ = Sw(x) dx C C с D + D d kips, Ey= M₂ E i E ZA x Ey X Incorrect If your answer for part (a) or (e) is incorrect, recall that concentrated loads create discontinuities in the shear-force diagram. Refer to the table below (Construction Rules for Shear-Force and Bending-Moment Diagrams), Rule 1. At…
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b=8.0 ft, c=4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A a B a b For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) W B W ÎÎÎÎÎÎ b C C d E d E X Ey X
Q7: The S ft wall shown here stands 27 ft from the building. Find the length of the shortest straight beam that will reach to the side of the building from the ground outside the wall. Beam Building Swall