A 500 mm diameter and 20 to long concrete pile is driven into a sand where y-18.5 kN/m' and 9-32". Assurning 6-0.84, determine the load carrying capacity of the pile, with a factor of safety of 3. Use Meyerhof's method for computing the point load-carrying capacity Q, and use Coyle and Castello (1951) method for computing the load-carrying capacity of the pile shaft O

A 500 mm diameter and 20 to long concrete pile is driven into a sand where y-18.5 kN/m' and 9-32". Assurning 6-0.84, determine the load carrying capacity of the pile, with a factor of safety of 3. Use Meyerhof's method for computing the point load-carrying capacity Q, and use Coyle and Castello (1951) method for computing the load-carrying capacity of the pile shaft O

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.3P: A 500 mm diameter are 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32....

See similar textbooks

Similar questions

A 400 mm 400 mm square precast concrete pile of 15 m length is driven into a sand where = 18.0 kN/m3 and = 33. Assuming = 0.7 and K = 1.4 Ko, determine the load-carrying capacity of the pile with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
A pre cast pile having a cross section of 0.20m x 0.200 is placed at a position as shown in the figure. The weight of the pile is 981 N acting at its centroid at G. The pile is resting at points A, B and C. Assuming smooth surface. Which of the following gives the reaction at point A,B,C.
Variation of N60 with depth in a granular soil deposit is given below. A concrete pile 9 m long with cross-section of 0.305m X 0.305m is driven into the sand. Then, estimate the allowable load-carrying capacity of the pile (Qallow). Use F.S.=4 and Meyerhof's equation for Qp and Qs. Depth (m) N60 1.5 4 3.0 4.5 7 6.0 7.5 16 9.0 18 10.5 21 11.0 24 12.5 20 14.0 19
63.A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely from a height of 1.5m. The total penetration of the pile in the last 5 blows is 40 mm. Use the engineering news record expression. Assume a factor of safety of 6 and empirical factor (allowing reducing in the theoretical set, due to energy losses) of 2.5 cm. The safe load carrying capacity of the pile
Please round to the nearest Hundredth (i.e., 0.01). No Comma! A square pile, 21 m long is driven into a homogeneous sand layer. The pile's width (diameter) is 0.4m. The standard penetration resistance near the vicinity of the pile is 12. Calculate the ultimate skin friction force (Qs) of the pile. Use Briaud & Tucker method. Hint: Qs = fs x As Qs = Answer kN
P-2 A driven closed-ended pile, circular in cross section, is shown in the Figure. Calculate the following: Layer I Groundwater 3 m táble a. The ultimate point load using Meyerhof's procedure. 3 m Layer II b. The ultimate frictional resistance Qs. [Take K = 1.4 and ô'= 0.6º'] c. The allowable load of the pile (use FS = 3 15 m Layer II d. Calculate the (a), (b) and (c) if the layer III was a Clay soil with C,=80 kPa (use ca-method by Terzaghi and FS = 3) %3D Layer I Y = 15.7 kN/m³ 4' = 32° Layer II = 18.2 kN/m3 Ysat = 19.2 kN/m³ Layer III 381 mm Ysat 4' = 32° c' = 0 = 40° c' = 0 c' = 0
P-1 A driven closed-ended pile, circular in cross section, is shown in the Figure. Calculate the following: Layer I Groundwater 3 m táble a. The ultimate point load using Meyerhof's procedure. 3 m Layer II b. The ultimate frictional resistance Qs. [Take K = 1.4 and ô'= 0.64'] c. The allowable load of the pile (use FS = 3 15 m Layer III d. Calculate the (a), (b) and (c) if the layer III was a Clay soil with C,=80 kPa (use a-method by Terzaghi and FS = 3) %3D Layer II = 18.2 kN/m3 Layer I Layer III Y = 15.7 kN/m³ o' = 32° c' = 0 19.2 kN/m3 381 mm Ysat 6' = 32° c' = 0 Ysat 4' = 40° c' = 0 Chabie Ch
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure P12.6, allowing a factor of safety of 3. Use K = 1.5 Ko and = 0.65 in computing the shaft load. Use Meyerhofs method for computing the point load.
A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Qp by a. Meyerhofs method b. Vesics method c. Coyle and Castellos method Use m = 600 in Eq. (12.28).
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2