A 50 hp, 250 V, 1200 r/min DC Shunt Motor with an armature resistance of 0.08 Q. Its field circuit has a total resistance (Radj + R) of 100 N, which produces no-load speed of 1200 r/min. (i) (b) Calculate the motor speeds when the input current at 100A, 200A and 300A. (ii) Using the result obtained from Q3(b)(i) plot the torque-speed curve of the motor. (iii) The motor in Q3(b) is now connected separately excited. The motor is initially running VA = 250 V, IA = 120 A and n= 1103 r/min, while supplying a constant torque load. Determine the speed of this motor be if VA is reduced to 200 V.

A 50 hp, 250 V, 1200 r/min DC Shunt Motor with an armature resistance of 0.08 Q. Its field circuit has a total resistance (Radj + R) of 100 N, which produces no-load speed of 1200 r/min. (i) (b) Calculate the motor speeds when the input current at 100A, 200A and 300A. (ii) Using the result obtained from Q3(b)(i) plot the torque-speed curve of the motor. (iii) The motor in Q3(b) is now connected separately excited. The motor is initially running VA = 250 V, IA = 120 A and n= 1103 r/min, while supplying a constant torque load. Determine the speed of this motor be if VA is reduced to 200 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A DC, separately excited motor is used to drive a constant-torque load. The field circuit is excited by a full-wave, AC/DC SCR converter. The armature circuit of the motor is connected to a constant dc voltage source of 160 V. The inductance of the field circuit is large, and the field current is continuous. The field AC voltage (input to the converter) is 147 V (rms), and the field resistance is 100 N. The armature resistance is 1.2 N. When the triggering angle of the SCRS is adjusted to zero, the motor speed is 1000 rpm, and the armature current is 10 A. Calculate the average current and dc power of the field i. A1 F1 circuit when the triggering angle is equal to 15°. La Ra If A a P; W M • If the motor speed is to be increased to 1400 rpm, what is the F2 A2 triggering angle? (a) Circuit a =
A DC, separately excited motor is used to drive a constant-torque load. The field circuit is excited by a full-wave, AC/DC SCR converter. The armature circuit of the motor is connected to a constant dc voltage source of 160 V. The inductance of the field circuit is large, and the field current is continuous. The field AC voltage (input to the converter) is 127 V (rms), and the field resistance is 110 N. The armature resistance is 2.2 N. When the triggering angle of the SCRS is adjusted to zero, the motor speed is 1300 rpm, and the armature current is 13 A. A1 • Calculate the average current and dc power of the field circuit when the triggering angle is equal to 15°. La Ra If 1.04 A Va M P¡ = 110.89 W A2 If the motor speed is to be increased to 1700 rpm, what is the triggering angle? (a) Circuit a =
Q6/ Answer the following questions: 1. Define the DC motor drive 2. Classify the DC motor drive 3. How can be controlling on the speed of DC motor 4. Numerate the types of AC-DC converter 5. Draw the circuit of single -phase converter on separately excited DC motor 6. Write the equations the following: I. Speed(W)= II. Torque developed(Td): III. Vm=..
A 48kW, 600V, 1500 rpm separately excited dc motor is controlled by single phase semi-controlled converter. The resistance of the armature is 192 and of the field is 1450. The field circuit is controlled by a single phase fully controlled converter and its firing angle is set to 20. The AC supply voltage to the armature and field converters is a single phase 220V, 60 Hz. The voltage constant is 0.946 V/A rad/s. If the armature converter firing angle is 45 and the speed is 1200 rpm; calculate the armature current and the developed torque.
A hybrid stepper motor is shown in Figure Q2(b). Demonstrate how the windings of the stepper motor are excited in wave drive mode to rotate the rotor 4 steps in the counterclockwise direction. Assume that Figure Q2(b) shows the starting position (to) of the stepper motor before the windings are excited. The first step (41) is given in Table Q2(b). (Note: Transfer Table Q2(b) to the answer script; tick the correct cells in the table to show the winding excitation sequence.) (b) Table Q2(b) Clock cycle Stator pole North pole South pole i (s) t2 (s) Al A2 B1 B2 Al A2 B1 B2 Clock eyele в (s) A2 14 (s) Stator pole North pole South pole AI B1 B2 Al A2 B1 B2 stator A1 AL armature N shaft PM armature 1- amature 2 armature 2 A A2 Figure Q2(b)
Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 n and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant. "Good Luck"
Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
1. Single phase full converter is used to control the speed of separately excited DC motors. AC supply voltage is 208 V. Motor armature and field resistance are 0.5 2 and 345 2 respectively. The field current is also controlled by a full converter and the field current is set as the maximum possible value. Motor voltage constant is 0.7 V/A-rad/sec. If firing angle is 45° and armature current is 55 A, determine the angular speed of the motor. Assume armature and field current are ripple free.
A shunt motor running on no-load takes 5 A at 200 V. The resistance of the fieldcircuit is 150 ohms and of the armature 0.1 ohm. Determine the output andefficiency of motor when the input current is 120 A at 200 V.
(b) A 2 pole 220 V, 100A, and 850 rpm separately excited DC motor has an armature resistance of 0.15 0. Two field coils are connected in parallel and used to drive a load with the torque of TL = 400 – 0.2N, Nm Where N is the motor speed in rpm. Armature voltage control and two field windings connected in series are used in speed control below and above the rated, respectively. (i) Calculate the motor armature current and speed when the armature voltage is reduced to 110VV. (ii) Examine the motor speed and current when field coils are connected in series.
A shunt motor is rotating at 1500 rpm and is powered by a 120V voltage source. The current line resistance is 51-A and the shunt field resistance is 120ohm. If the armature resistance is 0.12ohm, Determine: a) the armature current, b) the back emf (E), c) the total power that is supplied to the motor, d) the power absorbed by the armature, e) power dissipated in the armature. Please answer all subpart either dislike please I will like it please
A shunt motor is rotating at 1500 rpm and is powered by a 120V voltage source. The current line resistance is 51-A and the shunt field resistance is 120ohm. If the armature resistance is 0.12ohm, Determine: a) the armature current, b) the back emf (E), c) the total power that is supplied to the motor, d) the power absorbed by the armature, e) power dissipated in the armature. You have to answer all subpart not only first three subpart Either dislike is ready