A 480 Volts, 60HZ, 50Hp, three-phase induction motor is drawing 50 Amperes at 0.85 power factor lagging. The stator copper losses are 2KW, rotor copper losses are 700W, friction and windage losses are 600W, core losses are 1.8KW, and stray power loss is negligible. Find the following quantities: a. The air-gap power(PAG) b. The power converted(Pcony) c. The output power(Pout) d. The efficiency of the motor

A 480 Volts, 60HZ, 50Hp, three-phase induction motor is drawing 50 Amperes at 0.85 power factor lagging. The stator copper losses are 2KW, rotor copper losses are 700W, friction and windage losses are 600W, core losses are 1.8KW, and stray power loss is negligible. Find the following quantities: a. The air-gap power(PAG) b. The power converted(Pcony) c. The output power(Pout) d. The efficiency of the motor

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

1. The operation of Commutator in DC Motor is * O a) to convert dc to ac O b) to convert ac to dc O c) to convert fixed dc to variable dc O reverse the current direction in the rotating windings each half turn
Write a summary ( point) about equivalent cricuit of three phase induction motor .
2. Describe the Torque-Slip characteristics of a three phase induction motor.
8. A 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical power developed by the motor is ............ (i) 20 W (iii) 500 W (ii) 980 W (iv) 200 W
The winding of a 4-pole alternator having 36 slots and a coil span of 1 to 8 is short-pitched by ........... degrees. 150 40. 90 20 Brushless excitation system consisting of: Stator field winding and power diodes stator and rotor field winding and capacitor stator and rotor field winding and power diodes Everything mentioned in the options Full Name : *
The efficiency of 3-ph induction motor. at (Is=4.5A, T=13 N.m, N=1333 rpm, Pph=864 watt ) is
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
How to calculate the pitch factor of a 8 pole alternator with an armature wound coils having 18 / 24 fractioanl pitch. Can you please show the solution in details.
a) The rotor power output of a 3-phase induction motor is 15 kW and the corresponding slip is 4%. The rotor copper loss will be..
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
A three phase 6000 V alternator has the following O.C.C. at normal speed: Field current : 14 18 23 30 43 Terminal voltage: 4000 5000 6000 7000 8000 With armature short circuit and fall load current flowing the field current is 17 A And when the machine is suppling fall-load of 2000KVA at zero-power factor the field current is 42.5 A, and the terminal voltage is 6000 V. Determine the field current that required when the machine is supplying the fall-load current at 0.7 p.f. lagging.