A 40-cm-long, 800-W electric resistance heating element with diameter 0.5 cm and surface temperature 120°C is immersed in 75 kg of water initially at 20°C. Determine how long it will take for this heater to raise the water temperature to 80°C. Also, determine the convection heat transfer coefficients at the beginning and at the end of the heating process.

A 40-cm-long, 800-W electric resistance heating element with diameter 0.5 cm and surface temperature 120°C is immersed in 75 kg of water initially at 20°C. Determine how long it will take for this heater to raise the water temperature to 80°C. Also, determine the convection heat transfer coefficients at the beginning and at the end of the heating process.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.60P: 1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a...

See similar textbooks

Similar questions

A cylindrical rod with a diameter of 20 mm and a length of 300 mm is heated to a temperature of 200°C. The rod is then placed in a tank of water maintained at a constant temperature of 25°C. The convection heat transfer coefficient for the water is 2000 W/m²K. Determine the time taken for the temperature of the rod to reach 50°C.
For heat transfer purposes, an egg can be considered to be a 5.5-cm-diameter sphere having the properties of water. An egg that is initially at 8°C is dropped into the boiling water at 86°C. The heat transfer coefficient at the surface of the egg is estimated to be 800 W/m2-K. If the egg is considered cooked when its center temperature reaches 60°C, determine how long the egg should be kept in the boiling/water. Solve this problem using analytical one-term approximation method (not the Heisler charts). The length of/time for the egg to be kept in boiling water is determined to be min.
During a picnic on a hot summer day, the only available drinks were those at the ambient temperature of 90°F. In an effort to cool a 12-fluid-oz drink in a can, which is 5 in high and has a diameter of 2.5 in, a person grabs the can and starts shaking it in the iced water of the chest at 32°F. The temperature of the drink can be assumed to be uniform at all times, and the heat transfer coefficient between the iced water and the aluminum can is 30 Btu/h·ft2·°F. Using the properties of water for the drink, estimate how long it will take for the canned drink to cool to 40°F.
Ice water of 0°C is stored in a spherical container made of steel with an inner diameter of 3 m and a thickness of 1 cm. This container is located in a place where the external temperature is 25℃. The temperature of the entire container is assumed to be 0°C. If thermal resistance in the container is ignored, obtain (a) the heat transfer rate to ice water, and (b) the amount of ice that melts for 24 hours. The melting heat of ice at atmospheric pressure is 333.7 kJ/kg. The emissivity of the outer wall of the container is 0.75, and the convective thermoelectric transfer coefficient is 30 W/m2·K. The average temperature of the surrounding surface for radiation is 15℃. ***I would appreciate it if sir could write it in a way that I could read it well.**
4- Carbon steel balls 8 mm in diameter are annealed by heating them first to 900°C in a furnace and then allowing them to cool slowly to 100°C in ambient air at 35°C. If the average heat transfer coefficient is 75 W/m -°C, determine how long the annealing process will take. If 2500 balls are to be annealed per hour Given: Carbon steel [k = 54 W/m.°C, p = 7833 kg/m, and C,= 0.465 kJ/kg. °C. and a= 1.474x 10* m²/s] Air, 35°C Fumace Steel ball 100°C 900°C
. A small dam, which can be idealized by a large slab 1.2-m thick, is to be completely poured in a short period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m3. Suatu pelat datar dari besi dari seterika listrik berdaya 1200-
3- Stainless steel ball bearings have a diameter of 1.2 cm are to be quenched in water. The balls leave the oven at a uniform temperature of 900°C and are exposed to air at 30°C for a while before they are dropped into the water. If the temperature of the balls is not to fall below 850°C prior to quenching and the heat transfer coefficient in the air is 125 W/m² - °C, determine how long they can stand in the air before being dropped into the water. Given: Stainless steel [ k= 15.1 W/m.°C, p= 8085 kg/m3, and Cp= 0.480 kJ/kg.°C. and a=3.95 × 106 m³/s]
Steel rods (p = 7832 kg/m2, cn= 434 J/kg.K, and k = 63.9 W/m-K) are heated in a furnace to 850°C and then quenched in a water bath at 50°C for a period of 55 seconds as part of a hardening process. The convection heat transfer coefficient is 650 W/m2.K. If the steel rods have diameter of 40 mm and length of 2 m, determine their average temperature when they are taken out of the water bath. (Round off the answer to 1 decimal point.) °C
To warm up some milk for a baby, a mother pours milk into a thin-walled cylindrical container whose diameter is 6 cm. The height of the milk in the container is 7 cm. She then places the container into a large pan filled with hot water at 70°C. The milk is stirred constantly, so that its temperature is uniform at all times. If the heat transfer coefficient between the water and the container is 120 W/m2·K, determine how long it will take for the milk to warm up from 3°C to 38°C. Assume the entire surface area of the cylindrical container (including the top and bottom) is in thermal contact with the hot water. Take the properties of the milk to be the same as those of water. Can the milk in this case be treated as a lumped system? Why?
Consider hotdog being cooked in boiling water in a pan. Would the heat transfer be modeled as one-dimensional or two-dimensional? Would the heat transfer be steady or transient? Explain.
A pipe in a manufacturing plant is transporting superheated vapor at a mass flow rate of 0.3 kg/s. The pipe is 10 m long and has an inner diameter of 5 cm and a wall thickness of 6 mm. The pipe has a thermal conductivity of 17 W/m·K, and the inner pipe surface is at a uniform temperature of 120°C. The temperature drop between the inlet and exit of the pipe is 7°C, and the constant pressure specific heat of vapor is 2190 J/kg·°C. If the air temperature in the manufacturing plant is 25°C, determine the heat transfer coefficient as a result of convection between the outer pipe surface and the surrounding air.
Water is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 7-m-long tube. The tube is equipped with an electric resistance heater, which provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat generated in the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 8 L/min, determine the power rating of the resistance heater. Also, estimate the inner surface temperature of the pipe at the exit