A 300 mm X 500 mm exterior beam is reinforced with 25 mm main bars and 12 mm stirrups. The tension side has a steel area of 2450 mm² and the compression side has a steel area of 1480 mm². 60% of the tension steel area is laid out on the first layer, the remaining is on the second layer and the compression steels are on a single layer. Determine the following if the steel yield strength of the compression steel is 276 MPa, the steel yield strength of the tension steel is 415 MPa and the depth of the tension zone 340 mm: a. The compressive stress in the concrete.

A 300 mm X 500 mm exterior beam is reinforced with 25 mm main bars and 12 mm stirrups. The tension side has a steel area of 2450 mm² and the compression side has a steel area of 1480 mm². 60% of the tension steel area is laid out on the first layer, the remaining is on the second layer and the compression steels are on a single layer. Determine the following if the steel yield strength of the compression steel is 276 MPa, the steel yield strength of the tension steel is 415 MPa and the depth of the tension zone 340 mm: a. The compressive stress in the concrete.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

O Compute the maximum value of P that will not exceed a stress of bronze of 100 MPa. Bronze A=450 mm2 A=600 mm Aluminum Steel A=300 mm 2 Compute the max. value of P that will not exceed a stress of E-83 GPa E=70 GPs E=200 GPa aluminum of 90 MPa. 600 mm 1,000 mm 800 mm 3Compute the maximum value of P that will not exceed a stress of steel (3) of 140 MPa.
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
3. A steel baris l0mm diamelex and am lo It is stretched with a force of 20kN and exteads by 0-2mm- Calaulale e stress and strain.
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Problem 1.5-2 A bar of length 2.0 m is made of a structural stoel having the stres-strain dingram shown in the figure. The yield stresa of the steel is 250 MPa and the slope of the initial lincar part of the stress-strain curve (modulus of elasticity) is 200 GP. The bar is loaded axially until it eklongates 6.5 mm, and then the load is removod. How does the final length of the bar compare with its orig- inal length? Hint: Ue the concepts illustrated in Fig. 1-36h) MP 300 200 100 0.002 0.004 0.006
A 31 mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carry in KN when the steel grade is 60 and 40. Determine also it's elongation using the stresses if the modulus of elasticity of steel is 231 GPa. Determine also the weight if the length is 31 m and 03 m.
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
A strip of high-strength steel has a length of 30 cm and a cross section of 1 mm by 20 mm. The modulus of elasticity is 200 GPa and Poison’s ratio is 0.27. It is subjected to an axial load of 15000 N, and it is instrumented with two axial strain gauges with R= 120 Ω and a gauge factor of 2.10. The two fixed resistors are also 120 Ω, and the supply voltage is 2.5 V. The bridge is adjusted to zero voltage output before load is applied. Find the output of the bridge with load applied.
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
A 31 mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carry in KN when the steel grade is 60 and 40. Determine also it's elongation using the stresses if the modulus of elasticity of steel is 231 GPa. Determine also the weight if the length is 31 m and 03 m. Need it asap.
calculate the strength reduction factor at the minimum strain of extreme tension steel f'c=28 mpa and fy=420 mpa