A 3 mx 3m square spread footing is to support a 350 mm x 350 mm column carrying a dead load of 750 kN and live load of 500 kN. For concrete fc is 21 MPa and for steel, fy is 415 MPa. Use NSCP 2001 provisions. If the effective depth of the footing is 500 mm, find the number of 25 mm reinforcements. A 10 11 12 D 13

A 3 mx 3m square spread footing is to support a 350 mm x 350 mm column carrying a dead load of 750 kN and live load of 500 kN. For concrete fc is 21 MPa and for steel, fy is 415 MPa. Use NSCP 2001 provisions. If the effective depth of the footing is 500 mm, find the number of 25 mm reinforcements. A 10 11 12 D 13

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter11: Load And Resistance Factor Design (lrfd)

Section: Chapter Questions

Problem 11.3P: Repeat Problem 11.1 based on LRFD using the following factors: load factor for dead load = 1.25 load...

See similar textbooks

Similar questions

Design a square reinforced concrete footing to support a 20-inch square tied concrete column at the edge of the building as shown below. Also check development length and force transfer in the column and at the footing. Draw the reinforcement pattern. Use a footing thickness of 24". Assume the following design conditions: -service dead load= 270 kips -service live load= 135 kips -allowable soil pressure (q)= 5000 psf -f. for the column= 5000 psi -f. for the footing= 3000 psi -fy= 60000 psi -longitudinal column steel consists of #8 bars reinf cement is uncoated -unit weight of the soil is 125 lb/ft3 -normal weight concrete Finished ground line 20" square column Y = 125 lb/ft³ 5'
Design round column footing for 18 in diameter that supports loads of PD = 240 k and PL = 140 k. The bottom of the footing is 6 foot below final grade, reinforced concrete weight is 150 lb/ft3 and the soil weighs 100 lb/ft3 the allowable soil pressure is 5 ksf. The concrete strength is 4,000 psi and the steel is Grade 60. 2
H.W.1: One-Way Slab: 1. Check slab thíckness. 2.Check shear force. 3.Design flexural reinforcement for the slab. I 4.Dosign flexural roinforcement for continuous beam B. fe=28Mpa 6m 5.8m 5.8m 6m f,-420Mpa Slab h=250mm 6m Beam Section: ha600mm bw#350mm Column Section: 500x500mm 7m LL=5kN/m? Exterior D.L-4kN/m? 7m K
ASAP PLS I GIVE UPVOTE If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column has a 1.1m height from the top of the footing up to the finished ground line are both constructed, how much gravel (in m3) should be exactly used for a class B concrete mixture for the footing and the column (up to the finished ground line level).
SITUATION. A 3 mx 3 m square spread footing is to support a 350 mm x 350 mm column carrying a dead load of 750 kN and live load of 500 kN. For concrete f'c is 21 MPa and for steel, fy is 415 MPa. If the effective depth of the footing is 500 mm, find the number of 25 mm reinforcements. O O 13 12 10 11 9
Design a RC square footing by Ultimate Strength ACI Column dimensions: 14''x14'' LL= 100 k DL = 71 k qall= 4 ksf f'c = 3 ksi fy = 60 ksi
NEED IN 30MINUTES PLSS. If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column has a 1.1m height from the top of the footing up to the finished ground line are both constructed, how much gravel (in m3) should be exactly used for a class B concrete mixture for the footing and the column (up to the finished ground line level).
5-A 10ft continuous flexible strip footing is subjected to a load of 500 psf. Find the change in stress A - Below a point 3ft deep and 6ft perpendicular to the center of footing. B - Below the edge of the foundation at a depth of 3ft. C - Below the center of the footing at a depth of 3ft.
A simply supported 1 way slab having span of 3 meters is to carry the load for DL = 5kpa and LL = 4.8Kpa. If the concrete f'c = 28Mpa and rebar to be used is 10mm with fy = 276Mpa. a.) Determine the minimum thickness of the 1 way slab.(answer in millimeter in whole number) b.) Determine the Ultimate loading combination for the slab considering 1 meter strip?(answer in KN/m. in 3 decimal places ) c.) Determine the Ultimate moment for the slab considering 1 meter strip?(answer in KN-m. in 3 decimal places) d.) Determine the effective depth of the slab considering concrete cover = 20mmanswer in millimeter. in whole number e.) Determine the area of reinforcement for the slab based on the actual loadings.(answer in sq.mm. in 3 decimal places) f.) Determine the spacing of the rebar.(answer in millimeter(Don't round up, use actual value). in 3 decimal places)
roportion a trapezoidal combined footing for uniform pressure under dead load plus reduced live load with the following data in table. Distance c/c of column is 6 m and projection beyond column not exceed 0.5 m DL+Reduce dLL=175Kn/m2 DL+LL=230KN/m2 columnA DL=620KN LL=390KN column B DL=670KN LL=815KN
B; Design the area, strength design and effective bearing capacity of column footing, if qa= 10ksf, Fc' for footing=5000psi, Fc' for column= 4000psi, fy=40ksi, s.D.L=400k, sL.L=300k nd colum size=1ftx1ft (convert psi to ksi and all necessary unit conversion 5/
Determine the appropriate size of steel bars needed to confirm the development length requirements, the footing has a dimension of 2.0m x 2.0mx 0.8m. The column Section is 350mm x 350 mm Use a minimum protection of steel equal to 75 mm. fy use fc' = 20.7 mpa and fy= 415 mpa. using NSCP 2015.