A 250-V, 4-pole, wave-wound d.c. series motor has 782 conductors on itsarmature. It has armature and series field resistance of 0.75 ohm. The motor takesa current of 40 A. Estimate its speed and gross torque developed if it has a flux per pole of 25 mWb

A 250-V, 4-pole, wave-wound d.c. series motor has 782 conductors on itsarmature. It has armature and series field resistance of 0.75 ohm. The motor takesa current of 40 A. Estimate its speed and gross torque developed if it has a flux per pole of 25 mWb

Electrical Transformers and Rotating Machines

4th Edition

ISBN:9781305494817

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Harmonics

Section: Chapter Questions

Problem 3RQ

See similar textbooks

Related questions

Q: A coil of resistance 52 and inductance 120 mH in series with a 100 µF capacitor, is connected to 300…

A: Now, the below figure shows the circuit diagram of the given data :

Q: A dc shunt generator delivers 125 A load current at 250V. Estimate the emf induced if the armature…

A: Given Load current IL=125Avoltage V=250Varmature resistance Ra=0.05Ωshunt field resistance Rsh=50Ω

Q: mature (including brush contact) 0.1 Q, series field 0.02 Q, inter pole field 0.025 2, shunt field…

A: Given, Output=240×100 =24000W Total armature circuit resistance=0.1+0.02+0.025=0.145Ω Current,…

Q: A 220 V d.c series motor has armature and field resistances of 0.15 Q and 0.10 Q respectively. It…

Q: A shunt generator delivers 195 A at terminal p.m. of 250 V. The armature resistance and shunt field…

Q: Air-condition unit has 98 Kg is mounted on springs of stiffness k= 900 N/m with an assumed damped…

A: Given data: The mass of the AC unit is m=98 kg The stiffness of the spring is k=900 Nm The damping…

Q: A motor running 1800rpm transmits 10KW of power through a 25mm diameter shaft 1.2m long. What is the…

Q: ) Two 220-V. d.c. generators, each having linear external characteristics, operate in parallel One…

A: Given Eg1=270v, vt=220v , Ig1=35 A Eg2=280v , Ig2=50A Working in parallel connection

Q: a) A 6600V, 3 phase, star connected synchronous motor draws a full load current of 80 A at 0.8 power…

Q: what is unit impulse response?

A: Impulsive excitations are considered to be a large magnitude force that acts over a very short time…

Q: In a no-load motor, a constant electromagnetic torque of 5 Nm is generated at t = 0. The engine…

Q: A 10kW, 120V-DC series generator has an armature resistance of 0.1 ohms and a series field…

Q: A resistance of 2002 is connected in series with inductance of 318.3 mH capacitor, is connected to a…

A: As per the Bartleby answering guidelines we are supposed to answer first three subparts of the…

Q: In the experiment No.4, the core loss component current is given by. Ic Sindo lo Sindo Ic Coso lo…

A: Solution: Core loss consists of: Eddy current loss. Hysteresis loss.

Q: A 5.0V stabilised power supply is required to be produced from a 12V DC power supply input source.…

Q: Example 33.10. A 3-ph, delta/star connected 11,000/440 V, 50 Hz transformer takes a line current of…

Q: A 50 kg pump is to be placed at the midspan of a 2.8-m simply supported steel (E = 200 x 10° N/m²)…

A: Given:The natural frequency of the machine should be in the range of 50 to 75…

Q: 1Hydropower Plant System The following nametag is specification of a generator in a hydropower…

A: The energy of flowing water is converted into mechanical energy by a hydraulic turbine. This…

Q: Q.2. A highly inductive d.c. load requires 12A at 150V from a 230V single-phase a.c. supply. Give…

Q: One end of a light uniform rod is attached to a wall by a frictionless hinge. The rod is held in a…

Q: QUESTION 5 A 45kg machine is placed at the end of a 1.6m cantilever beam of the elastic modulus of…

A: As per Bartleby policy single question at a time kindly repost question 4 thanking you

Q: The input power to a 3-phase load is measured as 19kW. If the line voltage and power factor of the…

A: Given data: The input power to a 3-phase load is = 19 KW = 19000 W The line voltage of the load is =…

Q: flux density of 1.0 T in the airgap. The details are Number of turns, N = 400 The core is made up of…

Q: a why is the resistance of small machlnes high, and the reslstance of large machines low? why Is the…

A: (a) Why is the resistance of small machines high and the resistance of large machines low? The…

Q: a- For the AC supply having current expression (i 10 sin ( 1574 +30)) find the following? 1. Maximum…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Problem 6.1 Consider the sinusoidal voltage v(t) = 25 cos(400nt + 60°) V. %3D a.) What is the…

Q: In a dc machine design, if a wave winding with 8 poles is used, then the parallel path C must be…

A: Answer is 2

Q: 1. The armature and shunt field resistance of a 50-kW, 220 V shunt generator is 0.026 ohm and 52…

Q: What is the minimum static deflection of an undamped isolator that provides 75 percent isolation to…

A: Given data: Tr,ζ=1-0.75=0.25ζ=0N=5000 rpm Need to determine the minimum static deflection of an…

Q: See the attached file If the roots of characteristic equation are given by $1,2 = -3 damped natural…

A: Given

Q: Two shunt generators 1 and 2 are operating in parallel. The voltage of generator 1 falls from 240 V…

A: Given Data The voltage of generator A is: EgA=240 V The voltage of generator A fall to: Ia=220 V at…

Q: Two compound generators are operated in parallel. If generator A has a series-field resistance of…

A: We have given

Q: Convert a displacement of 2 mils peak 1,775 CPM to velocity in in./sec-peak.

A: Given data as per questionDisplacement,D=2 mils peak to peak f= 1,775 CPM

Q: A 3 lb motor is rigidly mounted in the middle of a 17.6 lb, 72 inch long beam, as shown in the…

A: Given:- Mass of the long beam=17.6lb Mass of the motor=3lb E=10 x 103 ksi I=0.625 in4 To find:- a)…

Q: A separately-excited DC generator supplies 30A to a load. If the armature resistance is 0.1 ohms and…

A: IF = 8A IL = 30 A E = 100 V (from the table) Ra = 0.1 Ω

Q: P14 Considering an undamped, forced oscillator (b = 0), show that Equation 15.35 is a solution of…

A: Write the equation 15.35 again and differentiate it. Differentiate again,

Q: The input power to a 3-phase load is measured as 6600 watts. If the line voltage and line current to…

Q: If you observe in your experiment that the peak efficiency of your motor occurs at ω=5.2 and T=0.054…

Q: A 4 pole DC generator has an armature winding containing a total of 648 conductors connected in two…

A: After solving the problem 1, the answer I got is 1250rpm, which is not in the options. I checked my…

Q: 4-18- A 15-hp, 220-V, three-phase, 60-Hz, 6-pole, Y-connected induction motor has the following…

Q: A fixed angle rotor exhibits a minimum radius, rmin at the top of the centrifuge tube of 3 cm and a…

A: Givenrmin=3 cm=0.03 mrmax=9 cm=0.09 mN=12000 rpmAskedRCFtop=?RCFbottom=?FormulaRCF=11.2×r×rpm/10002

Q: One end of a light uniform rod is attached to a wall by africtionless hinge. The rod is held in a…

Q: A motor generator set, as shown in Fig.24.13, consists of two armatures A and C connected with a…

Q: One end of a light uniform rod is attached to a wall by a frictionless hinge. The rod is held in a…

Q: An 8-pale r lapa wound armature rotuted at 350 rpm is required useful Flud per pole is No. of the…

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.
A dc shunt generator delivers 125 A load current at 250V. Estimate the emf induced if the armature resistance is 0.05 ohm and shunt field resistance is 50 ohms.
Example 7-3. A 460-V, 25-hp. 60-Hz, four-pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: - 0.641n X,-1.106 N R2 - 0.332 N X2 = 0.464 XM - 26.3 N The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2 percent at the rated voltage and rated frequency, find the motor's (a) Speed (b) Stator current (c) Povwer factor (d) Peony and Pout (e) Tiad and Toad Efficiency
Q1/ B/ A (220 V) series de motor runs at (400 rpm) and its useful torque is (100 Nm). If its efficiency at this load is (80% ), find the load current.
Question 2 Beli vifth Slack side Motor (imprut) Tight side Beli thickpess\ Centre distance Figure 2 Figure 2 shows an open flat belt drive connected to a motor and a pulley. The motor transmits 20 kw to the connect pulley of 450 mm diameter and is rotating at 850 r/min to a second pulley rotating at 400 r/min. The distance between pulley centres is approximately 2 m. The belt is 6 mm thick and has a density of 970 kg/m. The maximum stress in the belt is not to exceed 2,7 MPa. The coefficient of friction for both pulleys is 0,3. Determine: 2.1. The diameter of the second pulley. 2.2. The length of the belt. 3.3. The width of the belt taking centrifugal tension into account.
Q3) A 220 V d.c series motor has armature and field resistances of 0.15 Q and 0.10 Q respectively. It takes a current of 30 A from the supply while running at 1000 rpm. If an external resistance of 1 Q is inserted in series with the motor, calculate the new steady state armature current and the speed. Assume the load torque remains constant.
A 4-pole shunt generator with wave-wound armature has 41 slots, each having 12 conductors. The armature resistance is 0.05 ohms and shunt field resistance s 200 ohms. The flux per pole is 25 mWb, if a load resistance of 10 ohms is connected across the armature terminals, calculate the voltage across the load when generator is driven at 1000 rpm
B. A compound generator delivers 140 A at 300 V and the resistance of the shunt field, series field,and armature are 30 52, 0.2 52, and 0.1 S2 respectively. Calculate the electromotive force
A 480V, 3-phase, 50Hz 6-pole Induction motor with a rated power of 10KVA. (i) Calculate the synchronous speed in rad/sec (ws) (ii) Determine the rotor speed in rpm, if the % slip is 2.5%
The nameplate data of a separately excited DC motor is PN=5.5kW, UN=110V, In=80A, n=1000r/min. Try to plot its inherent mechanical properties of this motor.
QUESTION 1 Consider the equations of motion of an armature controlled DC motor given by Jw(t)+bw (t) Ki (t) = di (l) L + Ri (t) + Kw (t) = -Tfriction - Tload (t) Vin (t), dt where vin(t) is the input voltage and Tload(t) is the input load torque. The outputs are the armature current i(t) and the motor speed w(t). When the input voltage and torque are constant, the transient response of this system has the form of the homogeneous solution. What is the time constant of the transient response? Find the characteristic roots of this system first. Keep 3 significant figures, and do not include units. Use scientific notation. The constants are given below: Nominal voltage, Vin(t) = 17 V Moment of inertia of the rotor, J = 0.02 kg-m² Motor viscous friction constant, b = 0.009 N-m-s Friction torque, Tfric = 0.003 N-m Armature inductance, L = 0.1 H Armature resistance, R = 0.35 Back emf constant and motor torque constant, K = 0.21 N-m/A. **Recall that the time constant (or relaxation time) is…
Derive the equation of power transmitted by V-belt between two pulleys then find the cquation of length of the belt. Also discuss the advantage and disadvantage of power transmission with belts.