A 20-cm-diameter steel rod is subjected to a tensile load of 1000KN at one end and is fixed at the other end. Calculate the deflection of the rod if it is 150-cm long. (Esteel 200 GPa) PL d AE where d= end deflection of the bar in meter (m) P applied load in newton (N) %3D L = length of the bar in meter (m) %3D A = cross-sectional area of the bar in m E = modulus of elasticity of the material (N/m²) O 0.73 mm 0.1.51 mm 0.02 mm 00.24 mm

A 20-cm-diameter steel rod is subjected to a tensile load of 1000KN at one end and is fixed at the other end. Calculate the deflection of the rod if it is 150-cm long. (Esteel 200 GPa) PL d AE where d= end deflection of the bar in meter (m) P applied load in newton (N) %3D L = length of the bar in meter (m) %3D A = cross-sectional area of the bar in m E = modulus of elasticity of the material (N/m²) O 0.73 mm 0.1.51 mm 0.02 mm 00.24 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three solid cylindrical rods are welded together to form the compound axial member shown in the figure. The compound axial member is attached to a fixed support at A. Each rod has an elastic modulus of E = 47 GPa. Use the following values for the rod lengths and areas: L₁ = 1350 mm, L₂ = 1760 mm, L3 = 1300 mm, A₁ = 260 mm², A₂ = 155 mm², and A3 = 80 mm². What magnitude of external load Pis needed to displace end D a distance of up = 30 mm to the right? Part 1 8₁ F₁ = Part 2 8₂ F2 A = L₁ mm/kN (1) B L2 (2) Find the relationship between ₁, the elongation of rod (1), and the internal tensile force, F₁, in rod (1). Assume 8, is a positive value in units of mm and F, is a positive value in units of kN. So, the answer you enter for the ratio (8₁/F₁) must be in units of (mm/kN). mm/kN C L3 (3) D Similar to the previous step, find the relationship between 82, the elongation of rod (2), and the internal tensile force, F2, in rod (2). Assume 82 is a positive value in units of mm and F2 is a…
1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm C B V 100MPa -200 MPa E-80GPa ✓=0.3 G=30MPa
The figure above is a skycam which is supported by 2 wires (assume that no wires holding at the top of this device). Assume that the wires are 0.05 inches diameter. If the skycam weighs 77 lbs, then the tensile stresses of wire 1 and wire 2 are Blank 1 ksi and Blank 2 ksi respectively. SN= 77
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. A 12500*pi B 6250*pi 3125*pi 1563*pi
IV. An Aluminum bar AD (see figure) has a cross-sectional area of 250 mm2 and is loaded by forces P1 = 7560 N, P2 = 5340 N, and P3 = 5780 N. The lengths of the segments of the bar are a = 1525 mm, b = 610 mm, and c = 910 mm. (a) Assuming that the modulus of elasticity is E = 72 GPa, calculate the change in length of the bar. Does the bar elongate or shorten? (b) By what amount P should the load P3 be increased so that the bar does not change in length when the three loads are applied? (c) If P3 remains at 5780 N, what revised cross-sectional area for segment AB will result in no change of length when all three loads are applied? A k a B₁ P₁ b C P₂ -P3
A cantilever beam with a 'T' shaped cross-section is loaded with a distributed load as shown below. The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm. A y Parameter L a d 0 L B 777 Description Beam length T Width of the flange Height of the web Yield stress |←0 →| Value 250 80 75 250 y Units mm mm mm MPa You are tasked with ensuring the beam can withstand the applied loading. To do this you must: a) Calculate the centroid for the given cross-section. Your value of y should be measured from the bottom of the section. Determine an expression for Q (statical moment of area) for the given shape. The expression(s) for Q should be in terms of the variable, y, measured from the bottom of the section.
200 mm diameter rod is subjected to loads as shown. Determine the state of stress at points A and B. Show your results on an infinitesimally small square plane (please use the ones drawn below, which helps you in directions). 8 m 600 N 10 m 400 N 700 N B Txy Ox A
2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (sce figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile load P = 22 kN? (b) If the same volume of material is made into a bar of constant diameter d and length 2.4 m, what will be the clongation under the same load P? (c) If the uniform axial centroidal load q = 18.33 kN/m is applied to the left over segment 1 (sce figure part b), find the ratio of the total elongation of the bar to that in parts (a) and (b). Įd1 = 20 mm Įd2 = 12 mm %3D P= 22 kN 1.2 m- -1.2 m (a) q = 18.33 kN/m [d1 = 20 mm |d2 = 12 mm P = 22 kN 1.2 m (b)
A 50 mm diameter cylindrical aluminum block is connected to 2 hollowed cylindrical steel blocks as shown in Figure Q1. Both hollowed steel cylinders are of 60 mm and 40 mm outer and inner diameters respectively. The assembly is then connected to a rigid steel plate. Four bolts of diameter 10 mm are then used to rigidly fix the assembly to a wall. A force P is then applied to the assembly. The Modulus of elasticity(E) of steel is 200 GPa while aluminum has Modulus of elasticity(E) of 70 GPa. Both steel and aluminum have a yield strength(oy) of 250 MPa. The bolts have a yield stress (oy) of 800 MPa. All connections and joints are considered rigid. Q3 Determine the allowable value of P that can be applied to the assembly taking into consideration the yielding of all parts of the assembly and bolts. Use a factor of safety of 1.5. b. a. Based on the value of P obtained part (a), determine the total elongation of the cylindrical steel block. Based on the value of P obtained in part (a),…
The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and is made from 6061-T6 aluminum. (Figure 1) Figure 1.5 m • 300 N/m -2 m 1 of 1 > Part A Determine the vertical deflection of the bar at D when the distributed load is applied. Express your answer to three significant figures and include the appropriate units. dp = Submit μÃ Value Provide Feedback Request Answer Units
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 415 mm?, 636 mm² , and 253 mm² respectively.Determine the change in length (in mm) of the bar if P = 28084 N.The moduli of elasticity are 83.77 GPa for bronze ,71.95 GPafor aluminum , and 204.98 GPa for steel. Round off the final answer to four decimal places. Bronze Aluminum Steel 2P ЗР P. 4P 0.6 m →k 1.0 m 0.8 m Add your answer
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.8 in?, 1.07 in?, and 0.56 in? respectively.Determine the change in length (in inches) of the bar if P = 11280 Ib.The moduli of elasticity are 30092 ksi for steel,12006 ksifor bronze, and 10002 ksi for aluminum. Round off the final answer to four decimal places. Bronze Steel Aluminum 2 ft 4 ft 3 ft P 2P 3P 4P