A 10-kVA, 2300/230-V transformer is to be tested to determine its excitation branch components, its series impedances and its voltage regulation. The following test data have been taken from the primary side of the transformer: [CLO-1, PLO-2] (Marks-15) Open- circuit test Short- circuit test Voc = 2300 V Vsc = 48 V Ioc = 0.20 A Isc = 5.0 A Poc = 40 W Psc = 180 W The data have been taken by using the connections of open-circuit test and short-circuit test: Calculate the full-load voltage regulation at 0.8 lagging power factor and 0.8 leading power factor What is the efficiency of the transformer at full load with a power factor of 0.8 lagging

A 10-kVA, 2300/230-V transformer is to be tested to determine its excitation branch components, its series impedances and its voltage regulation. The following test data have been taken from the primary side of the transformer: [CLO-1, PLO-2] (Marks-15) Open- circuit test Short- circuit test Voc = 2300 V Vsc = 48 V Ioc = 0.20 A Isc = 5.0 A Poc = 40 W Psc = 180 W The data have been taken by using the connections of open-circuit test and short-circuit test: Calculate the full-load voltage regulation at 0.8 lagging power factor and 0.8 leading power factor What is the efficiency of the transformer at full load with a power factor of 0.8 lagging

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Similar questions

What are the advantages and disadvantages of back to back test on two similar single phase transformer?
3. Why the copper loss in the primary can be neglected, in the open circuit test? 4. Why the terms Rm and Xm significant when the transformer is loaded?
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes.
disadvantages of potential transformer.
What conclusions we come up with after doing open circuit test on single phase transformer.
Given a center tapped transformer, plot the output wave form. (Assuming practical model)
What are the objectives of conducting an open circuit test on single phase transformer?
1.a. For performing dielectric-strength tests on insulating materials, two transformers are connected in aA. parallel combination.B. cascade arrangement.C. polyphase arrangement. 1.b. In large power transformers, the unequal voltage distribution caused by voltage surges in the winding isprevented by the use ofA. static shields.B. series capacitors.c. low-voltage arresters.
What are the objectives of implementing an open circuit test on single phase transformer?
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
An AC source provides peak output Vi and peak current ii when connected to the coil primary of a transformer. The transformer has Np turns in the primary coil and Ns turns in the secondary coil. A resistance circuit R is connected to the transformer, see figure below. What is the equivalent resistance of the circuit?
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?