A 10-foot-tall concrete column (E-4200 ksi, Omax=2.4 ksi) is reinforced with four steel bars (E=29,000 ksi, omax=24 ksi) that run the full height of the column. If the steel bars each have a diameter of 0.75 inch, find the largest allowable value of P such that neither material exceeds its maximum stress. P P 10 ft a A B a 9 in. 19 in. Section a-a

A 10-foot-tall concrete column (E-4200 ksi, Omax=2.4 ksi) is reinforced with four steel bars (E=29,000 ksi, omax=24 ksi) that run the full height of the column. If the steel bars each have a diameter of 0.75 inch, find the largest allowable value of P such that neither material exceeds its maximum stress. P P 10 ft a A B a 9 in. 19 in. Section a-a

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.36P

See similar textbooks

Similar questions

AW310 × 74 wide-flange steel column with length L = 3.8 m is fixed at the base and free at the top (see figure). The load P acting on the column is intended to be centrally applied, but because of unavoidable discrepancies in construction, an eccentricity ratio of 0.25 is specified. Also, the following data are supplied: E = 200 GPa, y = 290 MPa, and P = 310 kN. What is the maximum compressive stress max in the column? What is the factor of safety n with respect to yielding of the steel?
A wide-flange column with a bracket is fixed at the base and free at the top (see figure). The column supports a load P1= 340 kN acting at the centroid and a load P2= 110 kN acting on the bracket at a distance S = 250 mm from the load P1The column is a W 310 X 52 shape with L = 5 m, E = 200 GPa, and y = 290 MPa. What is the maximum compressive stress in the column? If the load P1remains at 340 kN, what is the largest permissible value of the load P2in order to maintain a factor of safety of 1.8 with respect to yielding?
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
Find the amount of depression in mm at the midpoint of the bar AB. Mo= 1kNm, L = 1m, E = 200 GPa, I=1x106mm4
Find the amount of depression in mm at the midpoint of the bar AB.Mo = 1kNm, L = 1m, E = 200 GPa, I=1x106 mm4
The rigid beam in (Figure 1) is supported by the three suspender bars. Bars AB and EF are made of aluminum and bar CD is made of steel. al B st μA D 0.75 m 0.75 m 0.75 m 0.75 m PV P= Value al 2P F If each bar has a cross-sectional area of 415 mm², determine the maximum value of P if the allowable stress is (allow)st = 190 MPa for the steel and (allow)al = 150 MPa for the aluminum. Est = 200 GPa El = 70 GPa. Express your answer to three significant figures and include appropriate units. Units 2 m E ?
A reinforced concrete collumn 200mm in diameter is designed to carry an axial compressive load of 320kN. Determine the required cross sectional area of the reinforcing steel if the allowable stress are 6MPa for concrete and 120MPa foe steel. Use Eco=14GPa and Est=200GPa. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
A retaining wall 6 ft high is constructed ofhorizontal wood planks 2.5 in. thick (actual dimension)that are supported by vertical wood piles of a12 in. diameter (actual dimension), as shown in thefigure. The lateral earth pressure is p1 125 lb/ft2at the top of the wall and p2 =425 lb/ft2 at the bottom.(a) Assuming that the allowable stress in the woodis 1175 psi, calculate the maximum permissiblespacing s of the piles.(b) Find the required diameter of the wood pilesso that piles and planks (t = 2.5 in.) reach theallowable stress at the same time.Hint: Observe that the spacing of the piles may begoverned by the load-carrying capacity of either theplanks or the piles. Consider the piles to act as cantileverbeams subjected to a trapezoidal distribution ofload, and consider the planks to act as simple beams between the piles. To be on the safe side, assume thatthe pressure on the bottom plank is uniform andequal to the maximum pressure.
A circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force at joint B. If the outer diameter of the tube is 5 in. and the thickness is 3 - in., calculate the maximum normal stress in the tube (in ksi). (Include the sign of the value in your answer.) A 6 ft ed = 5 in. В V8 kips t= 3/4 in. 2.5 in. ksi