A 10 cm diameter solid aluminum post is subjected to a horizontal force of V-7 kN and a concentrated torque of T-8.4 kNm, acting in the directions shown in the figure below. Assume that i-0.5 m. The yield strength of the aluminum is oy 250 MPa, Determine at point K: a) Normal stress due to bending caused by V. Enter your onswer in MPa to 2 decimal places.

A 10 cm diameter solid aluminum post is subjected to a horizontal force of V-7 kN and a concentrated torque of T-8.4 kNm, acting in the directions shown in the figure below. Assume that i-0.5 m. The yield strength of the aluminum is oy 250 MPa, Determine at point K: a) Normal stress due to bending caused by V. Enter your onswer in MPa to 2 decimal places.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.2P: Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.

See similar textbooks

Similar questions

A 9 cm diameter solid aluminum post is subjected to a horizontal force of V= 8.4 kN and a concentrated torque of T= 7.8 kNm, acting in the directions shown in the figure below. Assume that L = 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places. b) Shear stress caused by T. Enter your answer in MPa to 2 decimal places. c) Apply the Maximum-Distortion-Energy Theory and calculate Mises equivalent stress. Enter your answer in MPa to 2 decimal places.
A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a concentrated torque of T = 7.5 kNm, acting in the directions shown in the figure below. Assume that L = 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places.
5) Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value of all shafts is same (50 mm) and material is steel (G-85 GPa) Dimensions in mm 40 500 Nm
Rod AB is fixed at side A with a length of 500m and a diameter of 20m. On side B, the rod experiences a torque of 2kN-m a compressive force of 10KN and a transverse force of 12kN. a) Find the stress state at center point C. b) Draw mohrs circle for the stress state. (Be sure to include principal values, A, B, sigma1 and sigma2) T= d%=20m 250m ZKN-m IOKN 7. A, 500m I2KN
A 10 cm diameter solid aluminum post is subjected to a horizontal force of V = 7.1 kN and a concentrated torque of T = 7.5 kNm, acting in the directions shown in the figure below. Assume that L = 0.5 m. The yield strength of the aluminum is σY = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places. b) Shear stress caused by T. Enter your answer in MPa to 2 decimal places. c) Apply the Maximum-Distortion-Energy Theory and calculate Mises equivalent stress. Enter your answer in MPa to 2 decimal places. d) Determine the factor of safety n. Enter your answer to 2 decimal places.
A9 cm diameter solid aluminum post is subjected to a horizontal force of V= 8.1 kN and a concentrated torque of T= 7.8 kNm, acting in the directions shown in the figure below. Assume that L = 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places. L
From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an outer d = 0.2m and thickness of 10 mm. Bar (b) is also a hollow bar with outer d = 0.15 m with same thickness as bar (a). If T1= 42,000 N-m and T2 = 18,000 N-m, Find the max shear stress in bar (b). Answer in MPa.
A solid steel bar with a circular cross-section has diameter 50 mm, length 1.5 m and shear modulus of 80 GPa. If the allowable shear stress is 48 MPa and the allowable angle of twist is 2.0 degrees, then what is the maximum permissible torque? State your answer in Nm to 1 decimal place.
The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of the block is 1cm. A shearing force applied to the top face produces a displacement of 0.015mm. Find the strain, stress and shearing force. Modulus of rigidity 4.5 x 10¹0 N/m².
F2 F3 F1 D 150 mm 350 mm
1: The forces as given below are applied as shown in the figure. Fi=10 kN, F2=5 kN and F3=3 kN. The diameter of the circular bar is 40 mm. Calculate the followings at point D; a) o and tp b) Principal stresses c) o, based on maximum principal stress theory d) o, based on maximum shear stress theory e) o, based on maximum deformation energy theory (Von Mises) F2 F3 F1 D 150 mm 350 mm
The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of the block is 1cm. A shearing force applied to the top face produces a displacement of 0.015mm. Find the strain, stress and shearing force. Modulus of rigidity 4.5 x 10¹0 N/m². **Need asap pls. Thank you.