A 1.8-m long rod that weighs 45N is placed on a circular horizontal board having a radius of 1.2m. The ends of the rod bear against the smooth circular rim around the edge of the table. The assembly is rotated at 100 rpm about the center of the table. Solve for the reactions on the rim at the ends of the rod. 1.8m r= 1.2m

A 1.8-m long rod that weighs 45N is placed on a circular horizontal board having a radius of 1.2m. The ends of the rod bear against the smooth circular rim around the edge of the table. The assembly is rotated at 100 rpm about the center of the table. Solve for the reactions on the rim at the ends of the rod. 1.8m r= 1.2m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.12P: The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical...

See similar textbooks

Similar questions

What is the ratio L/R for which the uniform wire figure can be balanced in the position shown?
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
A uniform beam that 10-m long is being supported by two men, one man at each end. The weight of the beam. Is 100-N. If the first man supporting at the right side exert twice as much as the second man on the left, where must a 50-N motor be placed (measured from the first man) on top of the beam? Show complete solution.
A hydraulic crane of total mass (including the mass of the boom) 53O0kg supports a load of 800kg. The boom mass 500kg is 7m long and makes an angle of 50 degrees with the horizontal. The boom's center of the boom length. Also assume that the center of mass of the crane excluding the boom acts at the middle of the outrigger jacks that are 4m apart. Draw the FBD of the crane and boom. Find the reaction force at the rear outrigger jack (Nr) and at the front (Nf) for the system to be in equilibrium. Assume the ground is friction less. 7m 1m
A 100-m, 10 N uniform rods carries 20-N and 30-N weights suspended at its ends, as shown. Where would the fulcrum be placed to balance the rod?
A circular plate is being supported by 7 outer springs and a central spring. The outer springs are equally placed around a bolt circle. Take note that the outer springs are 2 mm shorter than the central spring. Further, a 5000- Newton force is applied at the center of the plate pushing the springs down.
3. A uniform meter stick of length L = 100.0cm is held in equilibrium by two fulcrums A and B. The weight of the meter stick is 100.0 newtons. Fulcrum A is at the 12.0 cm mark of the meter stick. Fulcrum B is at the 62.0 cm mark of the meter stick. L A\ B 18 Calculate the force each fulcrum exerts on the meter stick in newtons.
A rod 6 ft. long rotates in a horizontal plane about a vertical axis through its center. At each end the rod is fastened to a cord 8 ft. long. Each cord supports a weight of W. a. Set up the equations of motion that are required to solve the problem. b. At what angle will the cord be inclined with the vertical if the speed of rotation is given at 18.42 rpm. 3' 3' 8' 8' w w
One end of a uniform 2.60m rod with a mass of 38.0kg is supported by a cable connecting one end to the wall so that the cable makes an angle of 42.0° with respect to the rod. The other end rests against the vertical wall, where it is held in place by friction so that the rod is perfectly horizontal. A sign with an unknown mass is hung from the rod 1.90m from the wall so that wall exerts a normal force of 1790N on the rod in the positive x-direction. What is the mass of the sign in kilograms?
NAME Question 1 (6/20) ANSWER ON THE YELLOW PAGES The nose wheel of the landing gear of an aircraft is extended and retracted by applying a torque M to the rod BC by means of an shaft located at point B. The rod AO, on which the landing wheel is also located, has a combined mass of 100 kg which may be simplified to a point force at point G. The masses of the bars CD and BC may be neglected. If the point D is located underneath point B, the rod CD is at an angle of 30° to the vertical y-axis. At this position the landing gear should be kept stationary, dynamic effects may therefore be neglected. All components are made out of stainless steel with max=200 MPa and Imax = 75 MPa. ALO d. 800 mm 400 mm 200 mm B 300 D M 500 mm OC 500 mm A D Questions, also draw all relevant free-body diagrams: a. Calculate the magnitude of the reaction force at point A. b. Calculate the minimum diameter of the pin in point A. The connection in point A is realized as shown on the right figure. Use a safety…
The cylinders in the figure shown are piled in a rectangular ditch as shown. The radii of cylinders A,B and C are 4m , 6m, and 5m respectively. Neglecting the friction. Determine the reaction between the wall and B in kN.
Problem A hollow right circular cylinder with diameter 200-mm shown below is open at both ends, rests on a horizontal plane as shown. Inside the cylinder are two spheres with their weights and radii given. The smaller sphere has a radius equal to 45 mm and the bigger sphere has 75-mm radius. Neglecting friction, determine the minimum weight of the cylinder so that it will not tip over. 200 N 500 N 200 mm