9. Ripple is a result of a. DC current being supplied. b. Transformer power loss c. AC current being supplied. d. Lack of transformer isolation 0.Ex 28. JAI xqVX 10. A 3cb 6 pulse generators would have a ripple or voltage drop of a. 13.5% b. 3.5% 89865 C. >1% d. 1-5% 29lduob JVI-I sit balduob zi d bensupa ai JVH odi,bolduob ai Val or Безвира гі 11. A high frequency generator is found in Togniniq asauso gniwollol all to a. Angiography sqoisvno zasig odi no gnut bosho b. CT c. Mammography sboi d. All the above 2

9. Ripple is a result of a. DC current being supplied. b. Transformer power loss c. AC current being supplied. d. Lack of transformer isolation 0.Ex 28. JAI xqVX 10. A 3cb 6 pulse generators would have a ripple or voltage drop of a. 13.5% b. 3.5% 89865 C. >1% d. 1-5% 29lduob JVI-I sit balduob zi d bensupa ai JVH odi,bolduob ai Val or Безвира гі 11. A high frequency generator is found in Togniniq asauso gniwollol all to a. Angiography sqoisvno zasig odi no gnut bosho b. CT c. Mammography sboi d. All the above 2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

a) The transformer has a turns ratio of 9.45, what is the dc load voltage considering the ripple voltage? b) The transformer has a turns ratio of 9.45, what is the dc load voltage without considering the ripple voltage?in 2 decimal places.
a) The transformer has a turns ratio of 9.45, what is the dc load voltage without considering the ripple voltage?b) The transformer has a turns ratio of 9.45, what is the peak-to-peak ripple voltage? c) The transformer has a turns ratio of 9.45, what is the dc load voltage considering the ripple voltage? Answer in 2 decimal places.
AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with 20 coils. What is the exiting voltage and current? a.) 1000v/0.1amp b.) 0.1v/1000amp c.)1000v/1amp d.) 2v/20amp e.) No change
help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
14/. The purpose of brushes in a dc machine is__________. to change ac to dc signal to remove the losses in machine to collect voltage from windings avoid spark for current
Given the center-tap fullwave rectifier circuit shown 220V 60Hz (+2) 220V:Es1-0-Es2 Es1 E$2 D1 D2 RL The transformer is rated 220V:12V-0-12V (Es1=Es2=12V) and the average current through the load RL is 400mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Power dissipated by the load RL. (c) Average current and PIV of each diode.
If the output voltage across the transformer secondary coil is Vm AC volt. a- Give a circuit to covert the Vm AC volt. to double Vm DC volt. b- Determine the voltage across each capacitor during the positive half cycle of the AC signal. c- Determine the voltage across each capacitor during the negative half cycle of the AC signal.
In a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic i.e, fast system response? How about when duty cycle changes slowly i.e, slow system response?
If the ratio of V/F has been kept constant and the observed value of hysteresis loss at rated frequency of 50 Hz is 18 W, the measured value of core losses is 35 W, Find the total core losses at the frequency of 60 Hz.
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
What is use of solenoid coil in the pressure to converter? a. To produce magnetic field in the LVDT b. To change the LVDT output c. To bring back the pivoted beam normal position d. To produce linear displacement in bellows
Voltage control method connected across the load, to supply part of VAR required is ..... O Shunt capacitor O tap changing transformer O series capacitor O booster transformer