-9- The plate shown in figure is at a uniform surface temperature of L=5m T, = 50°C. Heat is removed by convection to an ambient fluid at T 25 C . The heat transfer coefficient h varies along the surface 1,T. 2m H = 5m according to: h= 87 x Determine the total heat transfer rate from the surface. Answ(32917W)

-9- The plate shown in figure is at a uniform surface temperature of L=5m T, = 50°C. Heat is removed by convection to an ambient fluid at T 25 C . The heat transfer coefficient h varies along the surface 1,T. 2m H = 5m according to: h= 87 x Determine the total heat transfer rate from the surface. Answ(32917W)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.56P

See similar textbooks

Similar questions

are QAir flow across a 20m square is hape plate with velocity of 5 m/s force struem condition 1° c at 20 kpa heat in the plat surface furkshed furkshed constant heat at the wall So that the avrag wall is looc- calculate the surface heat flux and valae of heat Trasfer coff at X - Position of heat Transfer * те 8 = P-m-t Nu Re TW-T & их te limanel 4
This question about heat transfer/liquid. A horizontal wire of circular cross section with a diameter of d=1 mm is heated with electric current, and 100W(q'=100W/m) heat energy is given to the wire from 1m length. The wire T∞ = temperature at 20 ° C, large, compared to that in a stagnant water body, locate the outer surface temperature of the wire.
Q1) A polished metal pipe (8 cm) owtside diameter and 350 K temperature at the outer surface is exposed to ambient conditions at 285 K temperature. The emissivity of the surface is 0.3 and the convection coefficient of heat transfer is 13.5 Wim2-deg. What would be the overall coefficient of heat transfer by the combined mode of convection and radiation” Q2 find the pressure point (1) if the amospheric pressure is(70kpajihl =0 2,h2=0.4,h3=0. ‘)(p. =13600kg/m3. poil=850kg/m3)
Q1-A block as sphere made of Teflon initially at a temperature of 90 C is suddenly immersed in a fluid at 20 C. The convection heat- transfer coefficient is 15 W/m2 C. Determine the dimension of the block that it is just considered as lumped-capacity system. Calculate : (1) the time the center of the sphere reaches the half value of initial temperature and, (2) the heat loss from the block at that time.
Althih nlat plate 2 mby2 m is hanging freely in the air. The temperature of the surroundings is 25C. Solar radiation is faling on one side of the pate at the rate of 500 W/mThe emperature ot the plate wit remain constant at 30°C it the comvective heat transfer coefticient (in WimC) is b. 200 50
Air flow across a 20m square is hape plate with velocity of 5 m/s force struem condition are 10 at 2° kpa heaty in the plat surface furkshed constant heat at the wall that the avrag wall is lood - calculate the surface heat flux and valae of heat Trasfer coff at X-Posirtron of So * те P-m-t Nu- Re Fw-To te 7 timaneir heat Transfer тися - тов Tfa P= 2 P mut PP TW - Tax > Nu & q (LA) 0673 RE PY hix k 037
Heat transfer Calculate the heat transfer rate in Btu/hr through the pipe ona stainless steel pipe with a length of 12m has an inner diameterof 10in and an outer diameter of 13in. The temperature of theinner surface of the pipe is 50°C and the temperature of theouter surface is 48°C. The thermal conductivity of the stainlesssteel is 187 W/m-°C. Show complete solution in a clear paper.
Consider a pipe of 5 m in length and 1 cm in diameter. Temperature difference between the wall and the fluid (k = 1 W/mK) at exit is 25% that of at inlet. If the pipe wall temperature remains as constant of 80 ºC, total heat transfer rate 1000 W, and the flow is laminar what is the fluid temperature at inlet?
The thermal conductivity of a metal plata measuring CImxlm) ts (20 w/m.k) The plate is at a cmiform temperature af (80°c) heat to the suprounding air which is at (405) and heat transkr Coefficiont is (4ow/mk) Jt was attended to double, the heat loss by adding reatangular Lins to the surface, leach, fin is (im) loug the ns are spaced (45mm) Coyter to cnter heat trewster from Kin tips, and and lasses. tong (Snm) thick Neplecting . caleulate required height of ins 2
A 7 cm diameter bed on a 25 cm long bed, as shown in the figure below. The shaft rotates at 3200 revolutions per minute with uniform intervals of 0.2 mm. Continuous operation The temperatures of the shaft and bearing adjacent to the oil gap are 55 0C. your oil viscosity 0.05 N.s/m2 and its thermal conductivity is 0.17 W/m.K. Continuity, momentum and by simplifying the energy equations and solving for each separately, a) The maximum temperature of the oil, b) Calculate the heat transfer rates to the bearing and shaft.
(a)A block of coeight W shdes clown an inclined noite hibričatedy a fil Ihe film contact area f A and its thickpers is h. Asruming a linear velouty datribution in the film, derus an expression for the terminal (zero accefaration) veloGt, fhe W slides down an mof oit, figure below. inclined plane alA block then 4位66ck. Dfind the terminal velocty of He blocek in block mass Is 6kg, A = 35cn, @ =15° Gnd the film is Imm tnk SAE al at 20°C. fry belew, in #e Liqaid of thickiness,h Block contact area,A
Heat Transfer Questiion is image