8. The deflection of a simply supported beam is given by the BVP: y" - 10-7y = 10-8x(x – L) over 0SXSL with y(0) = y(L) = 0 %3D a. Determine the deflection of the beam using the shooting method (if you want to solve this by hand, use a large step, say h = 10. Otherwise code this and experiment numerically, for example investigate the effects of different step size. You may also add in Matlab "tic...toc" as a timer to calculate the time Matlab takes to solve your equation. You can explore how this time varies with different time steps, for example h 10; h 1; h 0.1) b. Determine the deflection of the beam using the finite difference method (same comments as in a.) %3D

8. The deflection of a simply supported beam is given by the BVP: y" - 10-7y = 10-8x(x – L) over 0SXSL with y(0) = y(L) = 0 %3D a. Determine the deflection of the beam using the shooting method (if you want to solve this by hand, use a large step, say h = 10. Otherwise code this and experiment numerically, for example investigate the effects of different step size. You may also add in Matlab "tic...toc" as a timer to calculate the time Matlab takes to solve your equation. You can explore how this time varies with different time steps, for example h 10; h 1; h 0.1) b. Determine the deflection of the beam using the finite difference method (same comments as in a.) %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Instruction: Solve the following problems about deflections of beam using Double Integration Method. 60N 1. Find the deflection of the beam shown: a) At 1 meter from the left support b) At the midspan c) At 4 meters from the left support 3m 3m Use flexural rigidity = EI R1 R2
Problem 2 (30 points): The formula for the deflection of the beam shown is: Wo y(x) = (-x5 + 5Lx-10L?x3 + 10L³x²) 120LEI Wo 15 x 107 N L = 2m %3D max m E = 7 × 1011 N m2 I = 6 x 10-4m Use the Newton-Raphson Method to determine the x location along the beam where the deflection is y(x) = 0.14 m. Use a starting guess of xo 1.2 m. Be sure to show your %3D calculation for the derivative of the function and your calculations you use to fill out the table. You only need to perform two iterations of the method, which means you should fill out the table below. Notice that y is defined as positive in the downward direction, which means that both the function and the target deflection are positive values in the coordinate system. y(xn) y'(xn) Xn+1 Step Xn 2.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam AB, (b) the deflection at the free end, and (c) the slope at the free end. Assume that El is constant for the beam. Let wo = 9 kN/m, L = 5.5 m, E = 220 GPa, and I = 100 x 10° mm“. |B L Part 1 Incorrect Cut a cross-section through the beam at any point and draw a free body diagram to the right of your cut. Determine the internal bending moment M(x). The diagram shows M(x) in its positive direction. Your answer may be negative. Check your equation by solving for M at x = 2.8 m. Wo M(x) |B L-x Answer: M(x = 2.8 m) = i ! kN-m
The beam ABC made of steel is receiving a point load P at the right end C. Please solve two problems from d to e. (a) Find the reaction from the supports A and B.(b) Use the double integration method to express the deflection y for the beam AB part as an equation for x (including E, I, P, a, L).(c) And use the following values to express the maximum value ymax of the deflection at the beam AB as mm. (Figure: I=300x106 mm4, E=200 GPa, P=200 kN, L=4.5 m, a=1.2 m)(d) Using the singularity function method, express the deflection y for the entire beam ABC as the equation for x (including E, I, P, a, L).(e) And use the following values to represent the deflection value yC at the right end part C as mm. (I=300x106 mm4, E=200 GPa, P=200 kN, L=4.5 m, a=1.2 m)
11. A simply supported beam is subjected to point load and uniformly distributed load as shown in Fig.(1). The maximum deflection at point C by using Macaulay Method in term of El of beam is given by; 11. A simply supportedbeam is subjected to pointload anduniformly distributedload as shown in Fig.(1). 40KN 15KN m Fig. (1) A D B 2mm 1m 7m The maximum deflection at point Cby using Macaulay Method in term of EI of beam is given by; a. -1260.61/EI b. -1460.61/EI c. -1660.61/EI d. None of the above
Q2 Use Finite difference method to solve the beam shown i Figure and find 1. The deflection at the points (1,2, and 3) 2. The moment at the point (1) 3. The shear at the point (2) The deferential equation is
Using Double Integration Method for the deflection of beams analyze the given structure below. 12KN/m 25KN 4m 5m 2m 2m SOLVE for the SLOPES at POINT B
0.0107 0.0043 0.0021 Let D= 0.0043 0.0085 0.0043 be a flexibility matrix, with flexibility measured in inches per pound. Suppose that forces of 40, 20, and 50 lb are applied to a beam at points 1, 2, and 3, respectively. Find the corresponding 0.0021 0.0043 0.0107 deflections y1. y2, and y3- #1 y1 = inch(es) (Round to the nearest thousandth as needed.)
1. Find the deflection y(x) where:The beam is embedded at x = L and a free end at x = 0. The applied load is w = w0*(1+Sin(πx/L)), wo is the maximum intensity of the load. Also, Find the overall deflection for 304 S.S. and an overall w0 of 3000 lbs. Please solve this using DIFFERENTIAL EQUATION METHOD. Other methods will not get upvote. Thank you.
Use the slope deflection method by using the graphical method to calculate deflections and draw bending moment diagrams then draw the shear force, axial force and bending moment diagrams.
Using the Double Integration Method. for the given cross- section of the beam below, find the ff. when E=100 GPa. a. Rotation in degrees and Deflection at 4-m from free-end. b. Maximum Deflection. 9 kN/m 25 kN.m. 1m 2m 3m 150 50 50 250 50
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a-9 ft, b=7 ft and w = 7.5 kips/ft. 21 Answers: Ay= W i a W B Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) 31 a b B b kips, Cy= C i C X Cy X kips.