8. A practical current source with a 1-A Fig. 3 short-cireuit current and 100-ohm internal resistance is to be used to deliver 1/12 A to a 100-ohm load. Determine an external resistance that can be placed across the source terminals, to achieve this result. Express the answer in ohms. А 14 в 10 C 6 D 2

8. A practical current source with a 1-A Fig. 3 short-cireuit current and 100-ohm internal resistance is to be used to deliver 1/12 A to a 100-ohm load. Determine an external resistance that can be placed across the source terminals, to achieve this result. Express the answer in ohms. А 14 в 10 C 6 D 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. Ans. r= 1.6 ohm 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. Ans. 2.667 V and 3.333 ohm 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the Internal resistance of the battery. Ans. 18.75 V and 0.75 ohm 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be…
В- for the circuit shown in figure 2, the resistance of both diodes is 7 0. In the practical model of the diode, determine the current through the resistor RI when: • Switch Si is ON and switch S2 is OFF • Switch Si is OFF and switch S2 is ON S1 D S2 D2 Figure 2 v2 10 v R1 850 0 V3
Procedure 1. Use multisim simulation package to simulate the circuit shown in the figure 5. Consider the following. Transistor type 2N2222A (NPN) and 2N3702 (PNP), Diode type (1N4007G). +20 V R 470 D Vut D2 RL 16 N V, R2 470 2 -20 V Figure 5.Class AB simulation circuit diagram. 3. Discuss the efficiency compared to class A power amplifier. i. he avan i
A circuit consist of a single diode and resistor which are connected to AC source. The resistance voltage is: O AC voltage with V=Vm/ O DC voltage with V= Vm/v2 O AC voltage + DC offset O only DC voltage with V=2Vm/
For the circuit below, determine the resistor voltage. The source is 6 volts, the Zener potential is 5.1 volts and the resistor is 1k.
Half-wave rectifier loaded with R-L is fed with a 120 VAA 60 Hz source. 10 Ω loadFind the inductance value that limits the average load current to 5A for the resistance.
In the circuit below, we have a Zener Diode circuit with a load, RL. Use the same measurements for source voltage V1 and resistor R3 resistance as in the circuit schematic. V1 -15V R3 2700 D1 1N753A RL Determine the lowest possible value for the load RL, so that the voltage drop across it is equal to the Zener voltage. For your diode, use model Zener 1N753A. This diode has a Zener voltage of 6.2V, a Zener current of 60mA, a Zener impedence of 72, and a test current of 20mA.
4 1.0 k VS2 VSI 25 V 8 V Diodes D1 and D2 in the figure are assumed ideal, what is the current through the diodes? * D₁ B R www C
Determine the voltage at resistor R1 if the Zener voltage is 5.1 V.
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
Diodes Are Connected In Series To Share A Total... 21 Question • Two diodes are connected in series to share a total reverse voltage of VD=D 5 KV. Reverse leakage currents of the diodes are ID1=30 mA and Ip2=35 mA. - Find Vp1 and Vp2 for R,=R2=100 k2 - Find R, and R2 for VD1=VD2 R1 VD1 Hint: Is=L,+IRj= I,2+IR2 VD R2 VD2
the non-inductive resistance of kelvin double bridge are set at 100ON each, the standard resistance is set at 0.10020 and the low resistance 0.0000122 was very low. determine the unknown resistance