Mechanics of materials II 8-10. A wood pipe having an inner diameter of 3 ft isbound together using steel hoops each having a cross-sectional area of 0.2 in?. If the allowable stress for the hoopsis oalow = 12 ksi, determine their maximum spacing s alongthe section of pipe so that the pipe can resist an internalgauge pressure of 4 psi. Assume each hoop supports thepressure loading acting along the length s of the pipe.4 psipsi

Given: σallow=12 ksip= 4psid= 3 ft = 3*12=36 inA = 0.2 in2

8-10. A wood pipe having an inner diameter of 3 ft is bound together using steel hoops each having a cross- sectional area of 0.2 in?. If the allowable stress for the hoops is aallow = 12 ksi, determine their maximum spacing s along the section of pipe so that the pipe can resist an internal gauge pressure of 4 psi. Assume each hoop supports the pressure loading acting along the length s of the pipe. 4 psi psi

8-10. A wood pipe having an inner diameter of 3 ft is bound together using steel hoops each having a cross- sectional area of 0.2 in?. If the allowable stress for the hoops is aallow = 12 ksi, determine their maximum spacing s along the section of pipe so that the pipe can resist an internal gauge pressure of 4 psi. Assume each hoop supports the pressure loading acting along the length s of the pipe. 4 psi psi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

13-10. A wood pipe having an inner diameter of 0.9m 0.9 is bound together using steel hoops each having a cross- sectional area of 125 mm. If the allowable stress for the hoops is o = 84 MPa, determine their maximum spacing s along the section of pipe so that the pipe can resist an in- ternal gauge pressure of 28 kPa. Assume cach hoop supports the pressure loading acting along the length s of the pipe. 28 kPa 28 kPa
A wood pipe having an inner diameter of 3 ft is bound together using steel hoops each having a cross-sectional area of 0.2 in. If the allowable stress for the hoops is σallow = 7 ksi, determine their maximum spacing s along the section of pipe so that the pipe can resist an internal pressure of 4 psi. Assume each hoop supports the pressure loading acting along the length s of the pipe.
5) The bolt has a diameter of 20 mm and passes through a tube with an inner diameter of 50 mm and an outer diameter of 60 mm. If the bolt and tube are made of A-36 steel, determine the normal stress in the tube and bolt when a force of 40 kN is applied to the bolt. Assume the end caps are rigid. 40 kN 160 mm 150 mm 40 kN
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 1st2allow = 150 MPa and the allowable bearing stress for the wood is 1sb2allow = 28 MPa. Assume that the hole in the washers has the same diameter as the bolt.
The gas pipe line is supported every 20 ft by concrete piers and also lays on the ground. The gas within the pipe is at a pressure of 500 lb/in?. The pipe has an inner diameter of 10 in, and thickness of 0.25 in. The material is A-36 steel. The pipe is shown in the figure below (Figure 1). Part A If there are rigid retainers at the piers that hold the pipe fixed, determine the hoop stress in the pipe if the temperature rises 75 °F from the temperature at which it was installed. Express your answer to three significant figures and include appropriate units. ? Value Units Submit Request Answer Part B Figure < 1 of 1 Determine the longitudinal stress in the pipe. 20 ft Express your answer to three significant figures and include appropriate units. HÀ
8–67. The metal link is subjected to the axial force of P=7 kN. Its original cross section is to be altered by cutting a circular groove into one side. Determine the distance a the groove can penetrate into the cross section so that the tensile stress does not exceed oallow better way to remove this depth of material from the cross section and calculate the tensile stress for this case. Neglect 175 MPа. Offer a the effects of stress concentration. P. 40 mm P 40 mm 25 mm Prob. 8–67
The bolt has a diameter of 20 (mm) and passes through a tube that has an inner diameter of 50 (mm) and an outer diameter of 60 (mm). If the bolt and tube are made of A-36 steel, determine the normal stress in the tube and bolt when a force of 40 (kN) is applied to the bolt. Assume the end caps are rigid. 160 mm 40 kN 40 kN 150 mm
Current Attempt in Progress The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w-70 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot ex t exceed 100 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pax that can be supported by the structure. Answer: Pax 3 KN
The rectangular bar is connected to the support bracket with a 24-mm-diameter pin. The bar width is w- 85 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax i kN
The steel bracket is used to connect the ends of two cables. If the allowable normal stress for the steel is sallow = 30 ksi, determine the largest tensile force P that can be applied to the cables. Assume the bracket is a rod havinga diameter of 1.5 in.
The links of the chains are made of steel that has a working stress of 300 MPa in tension. If the chain is to support the force P = 45 kN, determine the smallest safe diameter d of the links in mm.