7.4-11 An element in pure shear is subjected to stresses T, = 26 MPa, as shown in the figure. Using Mohr's circle, determine the following: (a) The stresses acting on an element oriented at a slope of 3 on 4 (see figure). (b) The principal stresses. Show all results on sketches of properly oriented elements. 26 MPa PROBLEM 7.4-11 3.

7.4-11 An element in pure shear is subjected to stresses T, = 26 MPa, as shown in the figure. Using Mohr's circle, determine the following: (a) The stresses acting on an element oriented at a slope of 3 on 4 (see figure). (b) The principal stresses. Show all results on sketches of properly oriented elements. 26 MPa PROBLEM 7.4-11 3.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.11P: An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using...

See similar textbooks

Similar questions

An clement in plane stress is subjected to stresses a,. cry, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis.
An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using Mohr’s circle, determine the following: (a) The stresses acting on an clement oriented at a slope of 3 on 4 (sec figure). (b) The principal stresses. Show all results on sketches of properly oriented elements.
-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,??y, and r. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-23 ??x= 2050 psi, sy= 6100 psi, txy= 2750 psi
An element in plane stress is subjected to stresses ?? = -8400 psi, ??y = 1100 psi, and (see figure). The material is aluminum with modulus of elasticity E = 10,000 ksi and Poisson’s ratio v = 0.33. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 30°, (b) the principal strains, and (C) the maximum shear strains. Show the results on sketches of properly oriented elements.
An element on the gusset plate in Problem 7.2-23 in uniuxial stress is subjected to compressive stresses of magnitude 6750 psi. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an element oriented at a slope of 1 on 2 (see figure). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. s
An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of crv = —45 MPa and rTb = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element.
A copper bar with a rectangular cross section is held without stress between rigid supports (see figure). Subsequently, the temperature of the bar is raised 50°C (a) Determine the stresses on all faces of the elements A and B, and show these stresses on sketches of the elements. (Assume = 17.5 × 10-6/? and E = 120 GPa ) (b) If the shear stress at B is known to be 48 MPa at some inclination 8, find angle
An clement in plane stress is subjected to stresses a, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an clement oriented at the angle 0. Now. The angle 0 is positive when count erclockwisc and negative when clockwise.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
-18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. 7.3-18 a=2I50kPa, ay=375kPa.Txy.=-460kPa
An clement in plane stress is subjected to stresses a,. cry, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an clement oriented at the angle 0. Now. The angle 0 is positive when count ere clockwise and negative when clockwise.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.