7. Water from the reservoir is pumped over hill through a 90 cm diameter pipe, and the pressure of 200 kPa is maintained at the summit, where the pipe is 90 cm above the reservoir. The flow is 1.40 m^3/s with a head loss of 3.0 m between the reservoir and summit. If the pump is 90% efficient, what is the input power furnished to the water in KW. A. 1865 B. 1954 C. 1734 D. 1923.

7. Water from the reservoir is pumped over hill through a 90 cm diameter pipe, and the pressure of 200 kPa is maintained at the summit, where the pipe is 90 cm above the reservoir. The flow is 1.40 m^3/s with a head loss of 3.0 m between the reservoir and summit. If the pump is 90% efficient, what is the input power furnished to the water in KW. A. 1865 B. 1954 C. 1734 D. 1923.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is being supplied with water from an open tank. The water level of the source reservoir is 6m below the pump center line. The length of the pipe (suction line ) is 10m and 50cm inner diameter with (coefficient of friction of .025). The atmospheric pressure of that altitude is 101325 Pa, and pump flowrate is 30O L/s. IF the vapor pressure of 20 °C water is at 2400 Pa, what is the NPSHa of the pump in meter? Your answer
A pump is needed to drain an excavation at a construction site. The excavation has alength of 50m, width of 50m, and a depth of 4m. The surface of the water in the excavation lies at adepth, H=3m, from the top the of the excavation. An old, radial flow, 1000W pump is immediatelyavailable for use; however, the total pump-motor efficiency, e, is only 50%. Estimate the drawdown inthe excavation in the first 4 hours of pumping. Neglect the change in H with increasing time. Neglectany head loss in the hose/pipe connected to the pump. (Hint: utilize the Pout equation, consider analternative definition of discharge as a change in volume over a change in time). Assume a specificweight of 9.79kN/m 3 .
The below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oiltanker to a refinery storage tank, both free surfaces being open to the atmosphere. Theeffective length—including fittings—of the commercial steel pipe is 6,000 ft. The dischargeat point 4 is 200 ft above the pump exit, which is level with the free surface of oil in thetanker. However, because of an intervening hill, point 3 is at a higher altitude than point 4.Losses between points 1 and 2 may be ignored.The crude oil has the following properties:Density ρ = 53 lbm/ft 3 ; Viscosity μ = 13.2 cP; Vapour Pressure Pv = 4.0 psia Answer the following questions:1. If the combination of pump and motor is 80% efficient, how much electrical power(kW) is needed to drive the pump?2. If, in order to avoid vapour lock, the pressure in the pipeline must always be above thevapor pressure of the crude oil, what is the maximum permissible elevation of point 3relative to point 4?3. If the flow in the pipeline…
The suction diameter of 60 mm reads 2 psi vacuum and 50 mm diameter discharge with 250 kpag. The suction water level is 5 m above water pump centerline with friction head loss of 0.5 m at suction pipes and discharge water level is 25 m above water pump centerline and head los at discharge pipe is 3 m. If discharge is 0.01 m^3/s, find the horsepower needed to pump the water for 70 percent pump efficiency.
Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water. Ignore any changes in Kinetic or potential energy and assume isothermal flow (ie. Internal energy is constant, this is normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump starting with full energy balance and simplifying to solve for the pump head symbolically. Then begin careful of unit, solve for pump head in feet. Given erosion 500 gpm P=62 lbs/ft^3 A- 10.5 ft B- 100.8 ft C- 50.1 ft D-80.7 ft
A pump delivers 2000kg/min of water (50°C) from reservoir A (El. 10m) to reservoir B (El. 40m). The suction line is 300mmx180m and the discharge line is 250mmx 50m. The pipes are made of wrought iron and the cavitation parameter as 0.2. Neglecting minor losses, find the reading of the pressure gage in mm Hg at the pump suction.
Water at 25°C is pumped at 1800 gal/min from the lower to upper reservoir, as shown in Figure below (Zı = 30 ft and z2 = 180 ft). Pipe friction losses are approximated by hf = 35V/2g, where V is the average velocity in the pipe. The pump is 80% efficient. (a) Find the head loss due to friction, hẹ in ft. in horse power (b) Compute the pump head, h, in ft and the pump power needed, Ppump (hp). Given: Specific weight of water, ywater = 62.4 lb/ft'; 1 ft/s = 448.8 gal/min. Show all calculations. Z2 = 180 ft Z¡ = 30 ft D= 6 in Pump
You were asked to design a water storage tank for your processing plant. The tank is cylindrical-shaped tank with diameter of 8.0 m. The water is to be supplied by a horizontal pipe (internal radius, ri = 6.00 cm), where water is under initial pressure of 2.00 atm., and flowrate of 2.0 m²/s. A vertical pipe (internal radius, rɔ = 1.00 cm) is to carry the water to a height of 9.40 m, where it is to pour out freely into the tank until the depth is 2.00 m. Assume water density of 1000 kg/m³, and g = 9.81m²/s. i) Calculate the volumetric flowrate and pressure at the pipe outflow.
A centrifugal pump is used to pump a liquid with the properties given below. Liquid is pumped from a storage tank at 95 kPa (a) to a discharge tank at 300 kPa (a). The system configuration is given in the table below. Table 1: system configuration Suction Discharge 4 50 Length (m) Diameter (m) 0.07 0.055 12 90° bends (L/D-35) 5 T piece (L/D=7) Gate valve (L/D-35) 1 1 1 2 Static height (m) 25 Liquid density = 1100 kg.m³ Viscosity = 1.5 x 10-³ Pa.s Vapour pressure of the liquid = 25 kPa (a) Material of construction of pipe is commercial steel, ε = 000045 m Table 2: Pump data 0 10 20 30 40 Flowrate (m³.hr¹) Head (m) 55 56 51 36 6 NPSH (m) 0 2 6 11 19 22 3.1. Graphically determine the optimal operating point of the pump in the above system using the pump data in Table 2. 3.2. Determine the NPSH of the system and determine whether the pump will cavitate when used in the above system.
Еxample4 A centrifugal pump is used to raise the water from the river to the reservoir, find: 1) total dynamic head. 2) water power, pump power and motor power. 3) monthly cost pump operation, if power cost is 4 cents and pump operates 20 hr/day. If:- 1- Q = 1.9 m/min 2- Elevation between the reservoir and the pump is 25 m and the length of the pipe is 365 m 3- Diameter of suction lift and discharge pipes 200 mm and length of suction lift is 10 m. 4- Barometric pressure is 88 Kpa, vapor pressure 2.5 Kpa 5- NPSH),eg = 40 Kpa 6- Efficiency of pump and motor is 80%. Treq 7- Neglect minor losses 8- Use f = 0.02, X= 10 Kn/m3
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
As shown in the figure, the water is directed downward in the installation with a 25 ° angle narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Where the flow is frictionless and gravitational effects are neglected, a) Find the effective pressure at point 2. b) Calculate the x and y components of the force needed to hold the elbow in place and the resultant force. (psu =1000 kg/m3, g = 9.81 m/s2).