STEP-UP CONVERTERS7-7 In a step-up converter, consider all components to be ideal. Let V, be 8-16 V, V, = 24 V(regulated), f, = 20 kHz, and C = 470 µF. Calculate Lmin that will keep the converter operatingin a continuous-conduction mode if P, > 5 W.7-8 In a step-up converter, Va = 12 V, V, = 24 V, I, = 0.5 A, L = 150 µH, C = 470 µF, and f,20 kHz. Calculate AV, (peak-peak).%3D%3D7-9 In Problem 7-8, calculate the rms value of the ripple in the diode current (which also flows throughthe capacitor).

“Since you have asked multiple question, we will solve the first question for you. If you want any…

7-7 In a step-up converter, consider all components to be ideal. Let V be 8-16 V, V, = 24 V (regulated), f, in a continuous-conduction mode if P, 2 5 W. %3D = 20 kHz, and C = 470 µF. Calculate Lmin that will keep the converter operating

7-7 In a step-up converter, consider all components to be ideal. Let V be 8-16 V, V, = 24 V (regulated), f, in a continuous-conduction mode if P, 2 5 W. %3D = 20 kHz, and C = 470 µF. Calculate Lmin that will keep the converter operating

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
DC to AC 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). (on for 10ms (+20V), off for 20ms, on for 10ms (-20V), off for 20ms, repeat) +20V 20ms 20ms 10ms ov 10ms -20V 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). +2-V -20V 10ms 20ms Oms 30ms 40ms
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
Single phase full wave controlled converter circuit is powered by a single phase source. When the trigger angle is 0 °, the DC output voltage taken from the output of the converter circuit is 300V. If the trigger angle is 60 °, what is the value of the DC output voltage to be obtained at the output? i have 1 houre
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
Trace the input and output voltage, current and voltage drops waveforms for single phase semi-converter converter with R load at α = 90⁰.
Design a buck converter such that the output voltage is 28V when the input is 48V. The load is 8Ohm. Design the converter such that it will be in continuous current mode. The output voltage ripple must not be more than 0.5%. Specify the frequency and the values of each component. Suggest the power switch also
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
Using an ideal diode, design a clamper circuit that result in the desired output waveform as shown in Figure Q7. Show overall analysis to justify the proposed design. 7. Vo Vi Designed Clamper Circuit - 3 V -20 - 43 V - Fiqure Q7 20
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A