67. Find the distance of the centroid from y-axis of the area bounded by the curve x=16y, the line x=12 and x-axis. a. 7 units c. 8 units b. 6 units d. 9 units 68. The are enclosed by the curve x² + y² = 25 is revolved about the line x-10-0. Find the volume generated. a. 4,934.80 cu. units b. 4,286.29 cu. units c. 5,230.16 cu. units d. 5,537.08 cu. units

67. Find the distance of the centroid from y-axis of the area bounded by the curve x=16y, the line x=12 and x-axis. a. 7 units c. 8 units b. 6 units d. 9 units 68. The are enclosed by the curve x² + y² = 25 is revolved about the line x-10-0. Find the volume generated. a. 4,934.80 cu. units b. 4,286.29 cu. units c. 5,230.16 cu. units d. 5,537.08 cu. units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H.W: Evaluate the integral 5. 2π π [ f(sinx + πο (sinx+cosy)dxdy
Locate the centroid of the area bounded by the x-axis and the sine curve y=asin(πx )/L from x = 0 to x = L. a.) x ̅=L, y ̅=πa/8 b.) None of the above c.) x ̅=L/2, y ̅=πa/16 d.) x ̅=L/2, y ̅=πa/8 e.)x ̅=L, y ̅=πa/16
Locate the centroid of the plane area. Given that a = 15 in. y 12 in.- 2 in.→— 21 in. The value of X = The value of Y in. F 6.94444 in. - ain. X
d²y and y = 1+t 4. Find dx dy if x= and dx? 1+t
Question 2 - Stress Transformation The state of stress at a point A on the surface of a beam is shown below, assuming the x - y coordinate system shown. A L The stresses point in the directions as indicated above, and have magnitudes given by: • %a = 25 MPa • Ob = 220 MPa T = 190 MPa y b) Find the in-plane principal stresses (assume 'maximum' refers to the most positive value): Omax = MPa Omin = MPa X Part One: Principal Stresses a) Find the in-plane principal angle at the point A on the surface of the pressure vessel, measured relative to the positive x-axis: Op degrees % Part Two: Mohr's Circle An example sketch of Mohr's circle for the state of stress is shown below. It is not drawn to scale, and it is recommended you draw your own Mohr's circle to perform the following calculations.
A point moves in a plane according to the equation x = t2 + 2t and y = 2t³ – 6t. Find dy/dx when t=0,2 and 5 respectively.
PROBLEMS Introductory Problems 2/1 The force F has a magnitude of 500 N. Express F as a vector in terms of the unit vectors i and j. Identify the x and y scalar components of F. Ans. F = 383i - 321j N, F, = 383 N, F, 321 N %3D 40 F = 500 N
P1 = 800 N and P2 = 450 N. Determine the sag yB of B and yD of D.
Force F= 2,000 N acts from A towards B. 275 mm A 550 mm 220 mm Determine the moment of the force about point C in N m. (The line of action for F does not pass through O. That illusion occurs due to the isometric drawing. Express your answer in vector form.) N-m Determine the shortest distance from point C to the line of action of the force in mm. mm
Tha). (9.26 displacment of Point D. Using the method of virtual work, find the vertical E = 29,000 Ksi. 1 in 2 2 3 31 All members have a cross- Sectional area of G 10 B. 3K ( с 4' 41% 3K down word 733 41 3k
consider the ff. w=xyz, x =s + 5t, y =s - 5t, z=st^2 a) Find partial w/partials & partial w/partial t by using chain rule b) Find partial w/partials & partial w/partial t by converting w to a function of s and t before differentiating.
Incorrect. Let a = ci +j and b = 6i + 8j. Find c so that the angle between a and b is-. Round your answers to four decimal places and enter the values in increasing order. C1 = i 2.3140 C2 = i 0.1204