6.74 One end of cable AB is fixed, whereas the other end passes over a smooth pulley at B. If the mass of the cable is 1.5 kg/m and the sag is H=1.8 m, determine the mass M that is attached to the free end of the cable.

6.74 One end of cable AB is fixed, whereas the other end passes over a smooth pulley at B. If the mass of the cable is 1.5 kg/m and the sag is H=1.8 m, determine the mass M that is attached to the free end of the cable.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.5) The bent bar as shown below is supported by a cable AE, a ball-and-socket joint at O, and a journal (slider) bearing at D. At the journal bearing D, the momen support reactions and the force support reaction along y-axis are zero. The 2-kip force and the 6 kip-ft couple-moment are parallel to z-axis and applied at point B. Determine the tension in the cable AE and the support reactions at O and D. X A / 0 4 ft Z 16 kip-ft 2 ft B 2 ft 2 kips BANES 3 ft [ 1 kip = 1000 lb. ] E 14 ft y
6.90 The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of the cable ABC is 20 m. Determine the horizontal force P that would hold the pulley in equilibrium in the position x- 5m. 16 m 14 KN Figure P6.90
Practice Problem 4.4.16: Find the force P required to (a) push; and (b) pull the 80- Ib homogeneous roller over the 3-in. curb. 24 in. 20°- 20° 13 in. (a) (b)
3.1 A uniform horizontal beam has a length of 8 m and mass of 500 kg. The beam rests on two supports overhanging one by a distance x while the other is at the extreme right-hand end. The loading is 5 tonnes at the left-hand end, 6 tonnes at the mid-point of the beam and 7 tonnes 1 metre from the right-hand end. Determine the value of x if the reaction at the left-hand support is to be twice that at the right-hand support.- Show free-body-diagram and all your workings.
The bent rod in Fig. a is supported at A by a journal bearing, at D by a ball-and-socket joint, and at B by means of cable BC. Using only one equilibrium equation, obtain a direct solution for the tension in cable BC. The bearing at A is capable of exerting force components only in the z and y directions since it is properly aligned on the shaft. In other words, no couple moments are required at this support. 1m B. 0.5 m Free-Body Diagram. As shown in Fig. b, there are six unknowns 05 m Equations of Equilibrium. The cable tension Tg may be obtained directly by summing moments about an axis that passes through points D and A. Why? 00 kg (a) Since the moment arms from the axis to T, and W are easy to obtain, we can determine this result using a scalar analysis. As shown,Fig. b EMDA = 0; Tạ(1 m sin 45°) – 981 N(0.5 m sin 45°) = 0 T = 490.5 N 0.5 m W 981 N 05 m D, (b)
The bent rod in Fig. a is supported at A by a journal bearing, at D by a ball-and-socket joint, and at B by means of cable BC. Using only one equilibrium equation, obtain a direct solution for the tension in cable BC. The bearing at A is capable of exerting force components only in the z and y directions since it is properly aligned on the shaft. In other words, no couple moments are required at this support. 1 m B 0.5 m .Free-Body Diagram. As shown in Fig. b, there are six unknowns 0.5 m Equations of Equilibrium. The cable tension T, may be obtained directly by summing moments about an axis that passes through points D and A. Why? 100 kg
The uniform rod AB has a weight of 10KN and is supported by a ball-and-socket joint at A and by the cord GC that is attached to the midpoint G of the rod. Knowing that the rod leans against a frictionless vertical wall at B, do the following: a) Label and name all forces that act on the rod. (You may use the given drawing. Assume the weight of the rod acts at G.) (4) 1.5 m 1.5 m b) Determine the tension force in the cable required to hold the rod in equilibrium (21) 4 m G 3m 0.75 75 m- 6 m.
0.2 m 0.7 m y 0.6 m D 0.9 m 0.4 m 0.3 m C E 0.9 m B 0.6 m 0.35 m 0.4 m 0.6 m x PROBLEM 3.59 The triangular plate ABC is supported by ball-and-socket joints at B and D and is held in the position shown by cables AE and CF. If the force exerted by cable AE at A is 55 N, determine the moment of that force about the line joining Points D and B.
SOLVE THE PROBLEMS WITH METHOD OF JOINTS AND METHOD OF SECTIONS 4.152 Compute the forces in members EF, NF, and NO. E F G n 5. M P 300 kN -8 pancls e 5 m = 40 m Dimensions in meters Fig. P4.152, P4.153 4.153 Repcat Prob. 4.152 assuming that the 300-kN force is applied at O instead of L.
(1) A 50 lb roller, with diameter 10 in, is used to level a tile floor, and is resting directly on the subflooring as shown. If the thickness of the tile is 30° 0.25 in, what is the minimum force P required to pull the roller onto the tiles when it is pulled slowly to the right? Fig. P4.75 and P4.76
4.46 The 90-kg man, whose center of gravity is at G, is climbing a uniform ladder. The length of the ladder is 5 m, and its mass is 20 kg. Friction may be neglected. (a) Compute the magnitudes of the reactions at A and B for x = 1.5 m. (b) Find the distance x for which the ladder will be ready to fall. =5 m 1.2 m -1.6 m --| Fig. P4.46
7.34 The cylinder and the block are connected by a horizontal cord. Determine the largest couple C that can be applied to the cylinder without disturbing the equilibrium of the system. Assume that both bodies are homogeneous.