6. a. Explain (include diagrams) the following components of Total drag on a solid object placed in a moving fluid. Include in your discussion how these components vary as the orientation of the object changes in the flow field: i) Pressure Drag ii) Friction Drag b. An antenna in the shape of a cylindrical rod projects from the top of an automobile. If the antenna is 106 cm long and 50 mm in diameter, calculate the drag force on it when the automobile is travelling at a velocity of 7.5 m/s in still air at -20°C Assume the surface of the structure is smooth.

6. a. Explain (include diagrams) the following components of Total drag on a solid object placed in a moving fluid. Include in your discussion how these components vary as the orientation of the object changes in the flow field: i) Pressure Drag ii) Friction Drag b. An antenna in the shape of a cylindrical rod projects from the top of an automobile. If the antenna is 106 cm long and 50 mm in diameter, calculate the drag force on it when the automobile is travelling at a velocity of 7.5 m/s in still air at -20°C Assume the surface of the structure is smooth.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 40 mm diameter plastic sphere (SG = 1.5) settles in a still water body. The required chart is as follows. a. Find the terminal velocity at which the sphere sinks b. What is the Drag coefficient CD? c. If the sphere starts to rotate counterclockwise at a speed of 50 revolutions per second, find the magnitude and direction of the Magnus force on it D Do 发送反馈 CD, CL 0.8 0.6 0.4 0.2 1 2 D PU²D² @ D Smooth sphere L PU²D² CD= Re= @D/2U UD V 3 = 6 x 104 4
Problem 14- A certain solid metal object weighs 60lb when measured in the normal manner in air, but it has such an irregular shape that it is difficult to calculate its volume by geometry. Use the principle of buoyancy to calculate its volume.a.) 0.216 ft^3b.) 1.216 ft^3c.) 2.216 ft^3d.) 3.216 ft^3e.) 4.216 ft^3f.) 5.216 ft^3
DYNAMICS OF RIGID BODIES UPVOTE WILL BE GIVEN.PLEASE WRITE THE COMPLETE SOLUTIONS CORRECTLY AND LEGIBLY. NO LONG EXPLANATION NEEDED. BOX THE FINAL ANSWER. A 1.09 kg block B is moving with a speed of 2.61 m/s as it strikes the 0.38 kg sphere A which was at rest. If the coefficient of friction between the block and the floor is μ = 0.27 and the speed of the sphere was 1.22 m/s immediately after impact, compute the distance (m) travelled by the block. Round off only on the final answer expressed in 3 decimal places.
Which could be the applied force in Newtons of a moving plate (area 0.1m2) and (v=2m/s) in between two different fluids: %3D over the plate: 3mm of Fluid 1 with viscosity of 0.001 Pa-s under the plate: 4mm of Fluid 2 with viscosity of 0.002 Pa-s O 0.18 O 0.17 O 0.19 O 0.15 O 0.16 O 0.20
A 40 mm diameter plastic sphere (SG = 1.5) settles in a still water body. The required chart is as follows. a. Find the terminal velocity at which the sphere sinks b. What is the Drag coefficient CD? c. If the sphere starts to rotate counterclockwise at a speed of 50 revolutions per second, find the magnitude and direction of the Magnus force on it D 发送反馈 0.8 0.6 0.4 0.2 1 2 D PU -D² (0 -D Smooth sphere L C₁ = Re= @D/2U UD V 3 = 6 x 104 4 5
Two identical billiard balls may move freely on a horizontal table. Ball A has a velocity of 0.4 m/s as shown, and hits ball B, which is at rest, at point C defined by  = 40 (the line of impact is along 40° path with respect to the horizontal direction). Assuming no friction, and knowing the coefficient of restitution between the two balls is 0.75, determine the velocity of each ball after impact
Problem: A homogeneous cylinder weighing 32.2 lb has a narrow slot cut in it as shown. A force of 12 Ib is exerted on a string wrapped in the slot. If the cylinder rolls without slipping, determine the acceleration of its mass center (a) and the frictional force F. Neglect the effect of the slot. |32. 2 lb I 18" 24 12 lb
9. Two balls A and B of masses 100 grams and 300 grams respectively are pushed horizontally from a table of height 3 meters. Ball has is pushed so that its initial velocity is 10 m/s and ball B is pushed so that its initial velocity is 15 m/s. a. Find the time it takes each ball to hit the ground. b. What is the difference in the distance between the points of impact of the two ball on the ground? Formula Vx = Vo cos 0 Vy = Vo sin 0 – gt x = Vo cos et y = Vo sin Ot – gt2
Two forces are acting on an object. One force is pulling the object with an upward direction to the right with a magnitude of 120 N and at an angle of 60 degrees with respect to the horizontal. The other force with a magnitude of 80 N pulls the object upward slightly to the left. The second force is 75 degrees with respect to the horizontal. A.) What is the magnitude of the resultant force on the object? B.) What is the direction of the resultant force?
Consider the flow of a viscous fluid parallel to a plate. You want to checkthe shear effort on the plate caused by the flow, known as the "force ofdrag." An analysis of the problem with the analysis of the relevant parameters suggests that the following variables should be considered: Strength that one wants to calculate F (values at the image) Length of plate L (L) Width of board B (L) Dynamic viscosity of the μ fluid Specific fluid mass ρ Fluid Speed V For the determination of the drag force on the prototype scale, for the flow of oil on the plate (dimensions B = 14 m; L = 35 m), the temperature of 20oC (μ = 1.0 ∙ 10−1 Pa ∙s; ρ = 924 kg/m3), a model will be used in the laboratory. The model has a scale scale of 1:20 (model:prototype) and will be tested in a water channel, the same temperature of 20oC (μ = 1.0 ∙ 10−3 Pa ∙ s; ρ = 1002 kg/m3). a. Determine the relationship between dimensional numbers by Buckingham Theorem Pi. Use the FLT system. b. Determine the L and B dimensions…
A 1000 kg car is pulling a 300 kg trailer. Together, the car and the trailer move forward with an acceleration of 2.15 m/s^2. Ignore any force of air drag on the car and all the friction forces on the trailer. Determine (a) the net force on the car, (b) the net force on the trailer, (c) the force exerted by the trailer on the car, and (d) the resultant force exerted by the car road *
Answer all .Determine the second moment of area of the shaded portion about the reference axis Y-Y shown in the below figure.figure is attached A bar of a certain material has 50 mm x 50 mm cross-section. When it is subjected to an axial pull of 150 kN, the reduction in each side is observed to be 0.00625 mm. Determine the modulus of elasticity and Poisson’s ratio of the material. The modulus of rigidity of the material is 50 GPa. A steel bar 60 mm in diameter and copper bar of 50 mm in diameter having lengths of 1.5 m each are rigidly fixed at one end as shown in figure. Determine the stresses in bars which causes shortening of compound bar by 0.9 mm from its original length due to the external load W. For steel, Es= 200 GPa, and for copper, Ec = 100 GPa.