6. A force of 85N is applied to a wrench in a clockwise direction at 62° to the handle and 21 cm from the center of the bolt. Find the magnitude of the torque and the direction that the bolt moves. Draw and label a diagram.

6. A force of 85N is applied to a wrench in a clockwise direction at 62° to the handle and 21 cm from the center of the bolt. Find the magnitude of the torque and the direction that the bolt moves. Draw and label a diagram.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.74P: It can be show that a plane area may he represented by a vector A=A, where A is the area and ...

See similar textbooks

Related questions

Q: A mass of 15 kg is at limiting equilibrium on a rough plane which is inclined at an angle of 40…

Q: Q1: Find the sum and magnitude of the sum and minus of the two .(vectors A(3,0,-7) and B (5,-4,-1

Q: What are the physical and thermal properties of water at 6 degrees celsi

Q: Q.1 Determine the force (P) shown in figure knowing that the resultant of two forcec passes through…

Q: Consider 9-cm long rod heated at both ends which follows a 1-D heat equation, With k = 0.82…

A: Given : To find :

Q: 1. Define the Tension test for rebars 2. Enumerate and explain different methods of Testing Steel 3.…

A: Since you have asked multiple questions, we will solve one question for you. If you want any…

Q: The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block…

Q: Q1) Determine the missing value's in the table. the forward divided differences are given by y(x)…

Q: A mass of 15 kg is at limiting equilibrium on a rough plane which is inclined at an angle of 40…

Q: 4.9 A piston/cylinder contains 50 kg of water at 200 kPa with a volume of 0.1 m³. Stops in the…

A: Write the given values with the suitable variables. m=50 kgP=200 kPaV1=0.1 m3Vr=0.5 m3T2=200 °C…

Q: Find the cross sectional area Stress=32.77 N/mm2 Force=3.7 N

A: Given data : Force=F Stress=σ To find : Cross sectional area

Q: Calculate the gage pressure in a 4 m^3 vessel occupied by 16 kg of N2O (behaving as ideal gas) at a…

A: Given data Volume of vessel = V = 4 m3 Mass of N2O = m =16 kg Temperature = T = 643 °C = 643 + 273…

Q: Discussion: 1. The effect of distance between blocks on the balance force.

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Which NEC table is used to determine the full-load current of a torque motor?

A: Full Load Current (FLC) torque motor : Full Load Current of a motor is defined as the motor which…

Q: Po Air R-22 FIGURE P4.31 4.31 A vertical cylinder (Fig. P4.31) has a 90-kg piston locked with a pin…

Q: What are two reasons for using an air spring? Explain the action of the conventional shock absorber…

Q: A pipe is replaced by two pipes in parallel that have half the diameter of the original pipe. What…

Q: ᴀᴛ 101.325ᴋᴘᴀ ᴀɴᴅ 13ᴅᴇɢᴄ ꜱᴜʀʀᴏᴜɴᴅɪɴɢ, ᴀ ꜱɪɴɢʟᴇ ꜱᴛᴀɢᴇ, ꜱɪɴɢʟᴇ ᴀᴄᴛɪɴɢ ᴀɪʀ ᴄᴏᴍᴘʀᴇꜱꜱᴏʀ ʀᴜɴɴɪɴɢ ᴀᴛ…

Q: For a certain polyatomic ideal gas the value of its ideal gas constant is 0.123 kJ/(kg.K). Determine…

Q: lever with an input of 2 meters has a mechanical advantage of 4. What is the output arms len

A: Given Input, I = 2 m Mechanical advantage, MA = 4 Find Output, O

Q: A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of…

Q: A supersonic wind tunnel is in the design

A: given P0=6*105PaT0=313 KA1=1.2 m2M1=3.5 AA*=1M2γ+11+γ-12M2.5γ+1γ-1

Q: Q. A house wall may be approximated as two 1.2 cm layers of fiber insulating board, an 8.0 cm layer…

Q: Hot oil ( Cp=2200 j/kg.°C) is to cooled by water (Cp=4180 j/kg.:°C) double pipe [shell- tube] heat…

Q: Find the strain Initial length=102.78 mm Change in length=0.004 mm

Q: a box with a mass 20kg pull with constant force P=W if the box was initial in rest wish one is the…

Q: www wwwwwww neser cevesse 400 250 500 ly= 1791666667 mm^4 O ly= 604166666.7 mm^4 O 300

Q: Compute the moment of area of the M diagram between the reactions about both the left and the right…

Q: The governing differential equation of a forced harmonic oscillation of a damped mass-spring system…

A: Given : To find : Oscillation of the system

Q: The braking torque on the drum is

A: Given data; External drum brake is shown in figure. Diameter,d= 500 mm Dimensions of the brake…

Q: A sewage aeration blower running at 3,500 rpm is designed to deliver 34,000 m3/hr of air from 20°C…

A: Solution: Given Data: N1=3500 rpmQ1=34000 m3/hrT1=20oCP1=1.03 kg/cm2P2=1.56 kg/cm2η=70%T2=43oC

Q: Hydroponic garden uses the 10-m-long perforated pipe system in Figure 1 to deliver water at 20°C.…

Q: * A mass of 15 kg is at limiting equilibrium on a rough plane which is inclined at an angle of 40…

Q: Contrast the governing physical assumptions that are made in analysing flow under models of both…

Q: 7.15 Two left-hand helical gears having the same helix angle are used to connect two shafts 60°…

Q: Find the rotation velocity of lead screw n and the velocity of liquid in syringe needle if the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: 9. Determine the moment of the 500 N force about point O, as shown.

Q: Find the velouty у сия K-E = 11773 K SS man= 55 kg

A: Given data : Kinetic energy=K.E Mass=m Required : Velocity

Q: Two forces F₁ and F₂ act on the screw eye. If the resultant force FR has a magnitude of 601b and the…

A: Solution - Given data -F1 =30lbFR =60lb

Q: A double-thread trapezoidal-metric-thread-form screw, which is driven by a motor, raises a nut and…

Q: Part B In the machine design the bed with a mass of 250 kg is moved by a lead screw which has a…

Q: 4ft R₁ 7ft 3P 7ft 4ft 2in k4in 8in 2in

A: Given

Q: write the shear and moment equations and draw the shear and moment diagram:

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: HW1: A gas flows through a horizontal pipe with cross-sectional area of 30 cm². At certain point,…

Q: A single ply of a certain graphite-epoxy composite with fiber oriented at 60° is in a planer state…

A: INTRODUCTION: The tensile stress developed when the load is passing through the longitudinal axis…

Q: The rotor of a gas turbine is rotating at a speed of 6900 rpm when the turbine is shut down. It is…

Q: 2. Air at 20° blows over a hot plate 50X60 cm made of carbon steel maintained at 220°. The…

A: From the data given in the question, Temperature of air = Atmospheric temperature = Ta = 20 oC Area…

Q: Determine the specific weight (lbf/ft^3) of a cubical body whose side is equal to 3.39 in. and has a…

A: Here, Mass of the body = m = 2.74 lbs Weight of the body = W = 2.74 lbf ( 1 lb mass experiences 1…

Q: . What is the energy stored in the spring if the spring iscompressed 0.5 m?

A: Given data mass = 40 kgspring constant = 3000 N/mCompressed length = 0.5 mWe have to find the energy…

Question

6. A force of 85N is applied to a wrench in a clockwise direction at 62° to
the handle and 21 cm from the center of the bolt. Find the magnitude of the
torque and the direction that the bolt moves. Draw and label a diagram.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

It can be show that a plane area may he represented by a vector A=A, where A is the area and represents a unit vector normal to the piano: of the area. Show that the area vector of the parallelogram formed by the vectors a and b shown in the figure is A=ab.
The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same magnitude of 20 N and are directed parallel to the long and short sides of the rectangle. The long side of the rectangle is twice as long as the short side. An axis of rotation is shown perpendicular to the plane of the rectangle at its center. A third force (not shown in the drawing) is applied to corner A, directed along the short side of the rectangle (either toward B or away from B), such that the piece of wood is at equilibrium. Find the magnitude and direction of the force applied to corner A.
The pistons in a car engine move up and down repeatedly to turn the crankshaft, as shown. Find the height of the point P above the center O of the crankshaft in terms of the angle .
Calculate the magnitude of the resultant for the force system shown in figure below. 600N SOON 407 30' 400N 300N
The following concurrent forces are acting on a body in xy plane: A 300 lb pointing up to the right 30 degrees with x axis, 400 lb at 45 degrees with x axis acting up to the left, 200 lb down to the left at 60 degrees with x axis, 150 lb down to the right at 75 degrees with x axis and a 100 lb directly to the right. Determine the resultant force and its direction using graphical and analytical method. Show solution, formula and the FBD and pls write legible
The following concurrent forces are acting on a body in xy plane: A 300 lb pointing up to the right 30 degrees with x axis, 400 lb at 45 degrees with x axis acting up to the left, 200 lb down to the left at 60 degrees with x axis, 150 lb down to the right at 75 degrees with x axis and a 100 lb directly to the right. Determine the resultant force and its direction using graphical and analytical method. Pls show the solution, formula and free body diagram.
$ Magnitude R= Direction 8 = Three forces act on point : A = 60 N at 135°, B = and C in this diagram to the correct magnitudes and directions. When this has been done correctly the dotted vector will become solid. 50 N at -45° and, C= 75 N at 60° 2. Pick up vectors A, B and C by their tails, and move them into a tip to tail arrangement. When this has been correctly done the resultant R will appear. measured Estimate the magnitude and direction of the resultant Based on this diagram, estimate the magnitude R and direction of the resultant. from the force R using the tip-to-tail method. 1. Move the tips of forces A, B, Submit part Submit part
In Figure, find the magnitude of Qopa if you know that the resultant of the three forces is a vertical force, and it is equal to 620N downward. A F=500N sol/ p=357.8N Q=240N To the left
The forces acting on the arm in the figure and the angles they make with the axes are given. Accordingly, find the force F2 that must be applied for the resultant force to be 900 N in the -x-axis direction and the angle θ it makes with the -y- axis .
3. Find the resultant force and its direction. Use the Ccmponent method. 100 N 110N 30 3ON 160N
Find the component of the force F = -7i + 8j – 9k lb along the line through the origin makingequal acute angles with the coordinate axes.
For the forces F and G, where: F is a force of magnitude 25N acting in direction i - 4j + 8k G is a force of magnitude 70 N acting in direction 2i + 3j - 6k (A) If G acts at the point (5, 2, 3), calculate the magnitude of the vector moment of G about the point (6,7, 25). Give your answer to two decimal places. (B) Calculate the magnitude R of the resultant force R = F + G. Give your answer in N, to two decimal places.