Find the stresses in members BC, BD, and CF for the truss shown in Fig. P-113. Indicate the tension or compression. The cross sectional area of each member is 1605 mm2. 3 m 3m c 4m 60 kN 90 kN 4 m Figure P-113

Find the stresses in members BC, BD, and CF for the truss shown in Fig. P-113. Indicate the tension or compression. The cross sectional area of each member is 1605 mm2. 3 m 3m c 4m 60 kN 90 kN 4 m Figure P-113

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter4: Plane And Space Trusses

Section: Chapter Questions

Problem 32P

See similar textbooks

Related questions

Q: Example 4.5 Calculate the safe load over a compression member of unsupported length of 48 m. The mem...

Q: If the soil matric potential is -15 bars in both a clay and sand, both soils will have the same hydr...

Q: -1 m -1 m -1 m 1 m 0.75 m Rod BC is made of A-36 steel and has a diameter of 40 mm. If P = 200 kN , ...

Q: For a rectangular beam, instead of vertical stirrups, inclined stirrups at 45° from horizontal are p...

Q: three Mohr's circles that dese stress in (Figure 1).

A: given:σx=-25ksiσy=25ksi

Q: In a falling head permeability test the initial head of 1.0m dropped to 0.35 m in 3 hours, the diame...

Q: (o') au a depth of 10 feet in a saturated clay layer if the water table is dropped from the ground s...

A: Given:- depth=10feet dropped by depth=20feet S=100% water content=35% Gs=2.75 To find:- change in to...

Q: THIS IS A SIMPLE BEAM WITH A SPAN LENGTH, L = 5M 2M 3M 5M R, R2 1. DRAW THE INFLUENCE LINES ALONG WI...

Q: An L-shaped structure is supported at A and D and subjected to two distributed loads and one concent...

Q: For the plate girder shown below, check the flexural strength, then shear strength on end and second...

A: Given, PD=60 kipsPL=30 kipsFy=50 ksi h=86 in

Q: How much is the strike separation (i.e., line AB on the map)? Scale: 18mm = 100m 82m 181m 67m 24m O ...

A: AB = 32 mm

Q: Solve for Ix, Iy, total Area, radius of gyration x, and radius of gyration y. All in inches and use ...

Q: A rectangular tubular column has the following properties: Nominal Width Along the X-Axis = 100 mm N...

Q: Water is flowing vertically upward in a sand with a saturated unit weight of 20 kN/m3. At what gradi...

A: Given-saturated unit weight=20 kN/m3

Q: The pin-connected rigid rods AB and BC are inclined at 0 the force P is applied, 0 becomes 32°. Dete...

Q: 200 lb Problem 1 A cantilever beam AB supports a couple and a concentrated load, as shown in the Fig...

Q: Consider a linear sinusoidal water wave with wave length 140m and 3-m wave height at 30m water depth...

A: The sum of the static pressure, dynamic pressure, and gravitational potential energy per unit volume...

Q: 400 lb-ft ft -5 ft

A: Given:- concentrated load=200lb couple=400lb-ft To find:- shear force and bending moment diagrams

Q: 5) The walkway ABC of the footbridge is stiffened by adding the cable ADC and the short post of leng...

Q: A steel weighing 490 lb/cu. has an ultimate strength of 80000 psi. what is the maximum length of the...

Q: urve is to connect 50 meters and 400

Q: Part A In (Figure 1), w = 1.7 kip/ft. Follow the sign convention. Determine the shear force acting a...

A: Given, w=1.7 kip/ft Span AB=18 ft

Q: För the figure shown below, determine the following: a. Maximum negative shear b. Maximum negative m...

A: Ra + Rb = 10 Rb x 10 + (2x5)x2.5 -30 = 0 Rb = -0.5 kn Ra = -9.5KN

Q: of 20 feet below the ground surface. The clay ha and G, = 2.75. Assume that no change in degree of :...

A: Given:- depth=10feet S=100% Gs=2.75 water content=35% To find:- change in total vertical normal and ...

Q: Force Reactions on a Structure 1 A cable supports an L-shaped beam subjected to a uniformly distribu...

A: ASKED: To determine: tension in the cable, T x-component of reaction at A, RAx y-component of react...

Q: Compute for the Shear and Moment Equation each segment. Compute the Reactions and Draw the detailed ...

Q: Problem 1: Water flows steadily from a tank, through a hose of diameter D = 40 cm, and exits to the ...

Q: Given that a circle is circumscribed about a hexagon, determine the area of the hexagon when the are...

Q: in its natural state. A moist soil has a volume of 9.34x10-3 m3 and weighs 180x10-3kN. The oven-drie...

Q: A circular sewer pipe 1.6 m in diameter is laid on a slope of 2 m per kilometer. The pipe is made of...

Q: Determine the diameter of the penstock, Runner and type of turbine Ø= 0.70 Given Data Head provided ...

A: We have to determine the value of diameter of the penstock, runner and type of turbine as per the gi...

Q: Problem A cantilever beam AB supports a couple and a concentrated load, as shown in the Figure. Draw...

Q: A Pratt roof truss is loaded as shown. Using the method of joints and the method of sections, determ...

Q: Fig. 1. etermine the dimension b if the shear stre Iso calculate the angle of twist for each b om (G...

A: Given:- T=1900Nm L=10m G=90GPa shear stress=60MPa angle of twist=0.015rad To find:- a)b b)angle of t...

Q: t of soil and concrete to be 16 kN/m3 and 24 kN/m3, respectively. The tot mate loads.

A: Data given column = 400mm×400mmfooting which is given =3m×3mfc'=21MPafy =414 MpaR/F =12-20mmD.L.=800...

Q: 55 kM y 70 kN/m В C 3 m 7 m

A: Given : Simply supported overhang beam with UDl, UVL and point loads

Q: 40R 40k 4) Determine the member forces in bars: AC, CD, DF & CF. 20K 144 30K 14 A 30K 14

A: Taking moment about point D FAC X 20 = 40 X 20 - 20 X 14 FAC = 10 kn ( Compressive)

Q: For the figure shown below, determine the following: a. Maximum negative shear b. Maximum negative m...

A: Take moment at B zero. Find reactions.

Q: The cross-section of a braced cut on a stiff, fissured clay (Y = 19 kN/m3, C = 40 kN/m2) is as shown...

Q: Design a prestressed beam using the elastic design method. Given, MT = 320k-ft, MG = 40k-ft, h =36in...

A: Prestress: The method of applying precompression to control the stresses in a concrete member. These...

Q: The frame shown in Figure 2 is part of the structure that supports an advertising panel. Determine t...

Q: 2.5 ft, 2.5 ft, 5 ft Rax 20 lb 40 lb Ray Rbx E Rby Сх Cy 10 ft C Dx Dy Ex Ey Both roller D.

Q: A triangular dam has a vertical upstream face 30 m high from the horizontal base. The depth of water...

Q: Q5. Determine the total number of bars in 2 tons of 6 m long and 10 mm diameter reinforcement steel ...

A: Asked: To compute the number of steel reinforcement bars from the given weight of bars. Given, Bat...

Q: Calculate the collapse load of a fixed end beam subjected to a load Wat one-third span. - 1/3 - M, 1...

Q: Problem 8 - 55 A rectangular echannel has a width of 3 m. If the discharge flowing in the canal is 2...

Q: Find the member forces and reactions for the truss with loading shown.

A: Given - To find - Find the member forces and reactions for the truss with loading shown.

Q: 200 lb Problem 1 A cantilever beam AB supports a couple and a concentrated load, as shown in the Fig...

Q: An 2014 T-6 aluminium flag pole with a hollow rectangular section experiences a wind force of 750 N ...

A: ultimate tensile strength : A tensile test is commonly used to determine ultimate tensile strength, ...

Q: 10.0 kN/m 19.8 kN 2.4 m B 21 31 00 41 31 51 19.8 kN 10.0 kN/m 3.6 m D E 31 41 31 51 G H 6.4 m 6.4 m ...

A: As per our company guideline, we are supposed to answer only 3 sub-parts. Kindly repost other sub-pa...

Question

100%

5. Find the stresses in members BC, BD, and CF for
the truss shown in Fig. P-113. Indicate the
tension or compression. The cross sectional
area of each member is 1605 mm2.
3 m
A
3 m
4 m
60 kN
90 kN
4 m
Figure P-113

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In Fig.4, The truss shown is under 2 k tension force. Use consistent deformation method to find the internal forces in all members. Hint: Select member AC as a redundant. 2k Fig.4 AE: Constant 3 ft 2k
1.20 Determine the smallest allowable cross-sectional areas of members CE, BE, and EF for the truss shown. The working stresses are 20 ksi in tension and 14 ksi in compression. (The working stress in compression is smaller to reduce the danger of buckling.) 30 kips 30 kips A 8 ft B 8 ft C 8 ft D E 18 ft F G FIG. P1.20
Q2. Determine the force in each member of the compound truss shown in Fig (2), below. 40KN SkN 4m 10KN C 1OKN D 4m 2m Im Fig (2)
Fig. 7.2. Using joint, section or graphical method, compute the stress of members BC, GC and GF of the truss given. O Hinge 1 — Figure 8.1 Hinge Figure 8.2 Hinge 100 lb Figure 8.3 AL 8.1 through 8.5. Classify each of the structures shown as unstable, statically determinate, or statically indeterminate. If the structure is statically indeterminate externally. 2 10.00ft Hinge 200 lb B G₁ 10.00ft 30.00ft 200 lb Figure 7.2 7 10.00ft Figure 8.4 Figure 8.5 6 8
H.W.pdf Süu Q1/ For the indeterminate structural Truss shown in Fig-1, use the method of consistent deformations to find the vertical reaction at support (C); noting that EA is constant for all members. 15 KN 15 kN (Fig-1) 1.5 m 1.5 m E 2 m 2 m 1 Add file
Question 19 Find the forces in members FH, EF, DE and CD of the truss shown in Figure Q19. K 4 m H 30 kN G 4 m Figure Q19 30 kN C 4 m OB 6 m Answer: FH = 25 KN, FEF=-15 kN, FDE = 0,FD=0
Q2: Analyse the truss shown in Fig. 2 using substitute member method. 1 KN d 4m 1 kN C 3m Fig. 2
Q2. Determine the force in each member of the compound truss shown in Fig (2), below. 40kN SKN 4m 10KN C 1OKN ID E 4m A B Im im Im lu 2m Fig (2)
Problem No. 2. Find the stresses in members CD, BC, and CE for the truss shown. The cross-sectional area of each member is 4 in.2. Indicate whether the stresses are tensile (T) or compressive (C). B C 50° 50° 50° 50° D E | 20 kips
3. For the truss shown in the figure for this question, members AB and CD shown in bold each have a weight of 2 N. 4 m IC Establish the force in members BC, E I 3. CG, DE, and GH. Ans. FBC = 8 N (tension) FCG = 1.67 N (compression) FDE = 0 FGH = 6.67 N (compression) %3D 5 N 2N 7 N %3D %3D
PROBLEM 07: The figure shows a truss and the sequence of assembly of members at pins H, G, and F. All members of the truss have cross-sectional areas of 250mm2 and all pins have diameters of 15mm. Determine the following: a. Axial stresses in members HA, HB, HG, and HC. b. The maximum shear stress in pin H. G H HC HG HB HA GF A 130° B 30 E GH +3 m--3 m→-3 m-→--3 m- ¥4 kN V2 kN ¥3 kN Pin H Pin G Pin F
PROB. 1. For the truss shown in Fig. 1, Calculate the stresses in members CE, DE and DF. The cross-sectional area of each member is 1500 mm² A 2.0 M B C 1.5M 4⁰ KN Fig. 1, 2.0 m E (1) 1.SM D 2.0 m 50 KN F