4_In compression testing, test-pieces have to be short and the length not be greater than three times the diameter. 5_In compression test, once plastic deformation occurs the material tends to deform into a barrel shape Q_Give reason(s) for the following: 6- In compression test, the shape of plastic portion of stress-strain curve is different from its tensile test complement in that higher values of engineering

4_In compression testing, test-pieces have to be short and the length not be greater than three times the diameter. 5_In compression test, once plastic deformation occurs the material tends to deform into a barrel shape Q_Give reason(s) for the following: 6- In compression test, the shape of plastic portion of stress-strain curve is different from its tensile test complement in that higher values of engineering

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw a typical stress vs strain tensile test curve for the following materials (two seperate graphs) and label the axis. A ductile metallic test specimen that is stretched to failure displaying a characteristic yield point and show the following parts on the curve. 1- Yield point 2- Ultimate Tensile Strength 3- Breaking point 4- Elastic Region 5- Plastic Region 6- Necking region
Draw a typical stress vs strain tensile test curve for the following material and label the axis. A typical brittle material subjected to a tensile stress that has been applied to the material till the sample breaks. 1- label the axis and draw the curve for a brittle material. 2- indicate the maximum strength of the material. 3- show on the portion of the curve where young's modulus can be calculated.
In a tensile test, the engineering strain has been calculated as 0.5. What is the value of true strain: 0.505 0.405
C1. A mild steel tensile specimen of initial length 41 mm and initial diameter 6.2 mm is subjected to a tensile test and the following data are obtained. Yield Strength as 115 MPa Maximum Strength as 210 MPa Fracture Strength as 168 MPa Percentage of Elongation as 50 % Percentage of Reduction in area as 32% Determine the Final length, Final area, Yield load, Ultimate load & Fracture load. The yield load in N is The Ultimate load in N is The Fracture load in N is
A tensile test was performed on a metal specimen with a diameter of 1/2 inch and a gage length (the length over which the elongation is meas- ured) of 4 inches. The data were plotted on a load-displacement graph, P vs. AL. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/AL = 1392 kips/in. What is the modulus of elasticity? BI
Consider the tensile stress-strain diagram below. If samples 1 and 2 are identical except that they were tested at different temperatures, which sample was tested at a lower temperature? Note: This question will be marked negatively so consider your answer carefully. A. Sample 1 B. Both were tested at the same temperature/ Alby is by die dieselfde temperatuur getoets C. Sample 2
In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final) of specimen after tensile test was 264.327. The load which caused fracture was (122.5 KN). After fracture, the final length was 47.516mm The true stress at fracture is less than engineering stress at fracture True False
The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of testspecimen was 0.505 inch and gauge length was 2.0 inch. Plot the stress strain diagram and determine(a) Proportional Limit (b) Modulus of Elasticity (c) Yield Stress at 0.2% offset (d) Ultimate Stress and(e) Nominal Rupture Stress.
In the First project: you have been asked to perform tensile testing for four different materialsand analyse the results and work on some NDT process selection:a. For the results shown in Table 1 of the tensile testing that you have performed, find thefollowing, if you know that the original length of specimen is 20.8 mm and the original diameteris 6.4 mm. Fill the calculated results in the summary table below (Table 1):1. Plot the engineering stress versus engineering strain for each material and L-D Diagram.2. Compute the modulus of elasticity, E in GPa.3. Determine the yield strength at a strain offset of 0.002.4. Determine the tensile strength in MPa.5. What is the approximate %El ductility, measured by percent elongation?6. Compute the modulus of resilience.7. Determine the fracture stress in MPa.8. Compute the final area (Af) in mm2.
The following stress-strain curve was prepared based on a tensile test of a specimen that had a circular cross-section. The gage diameter of the specimen was 0.25 inches and the gage length was 4 inches. The stress scale of the stress-strain diagram is given with the factor a = 10 ksi. Estimate: (a) The modulus of elasticity. (b) The ultimate strength. (c) The yield strength (0.2% offset). (d) The percent elongation at fracture. 2013 Michael Swanbom STRESS VS. STRAIN BY NC SA 7a bat Sat 2at at 0.05 STRAIN 0.01 0.04 0.06 0.08 0.02 0.03 0.07 0.09 STRESS
The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the propotional limit, modulus of elasticity (i.e the slope of the initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percent reduction area. TENSILE-TEST DATA Load(kN) Elongation(mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20 mm. During the test the specimen yields under a load of 100,000 N. The corresponding gage length = 50.5 mm. This is the 0.2% yield point. The maximum load of 180,000 N is reached at a gage length = 65 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage length of 73 mm, determine the ductility. i need clear ans by hand and solve very very fast in 20 min and thank you | DYBALA