4-10. The dimensions of a jib crane are given in the figure. The crane has a mass of 800 kg and a center of mass at G. The bearing at A is a journal bearing and can support a horizontal force, whereas the bearing at B is a thrust bearing that supports both horizontal and vertical components. Determine the maximum load F that can be suspended from the end of the crane if the bearings at A and B can sustain a maximum resultant load of 24 kN and 34 kN, respectively. -3m- 0.75m

4-10. The dimensions of a jib crane are given in the figure. The crane has a mass of 800 kg and a center of mass at G. The bearing at A is a journal bearing and can support a horizontal force, whereas the bearing at B is a thrust bearing that supports both horizontal and vertical components. Determine the maximum load F that can be suspended from the end of the crane if the bearings at A and B can sustain a maximum resultant load of 24 kN and 34 kN, respectively. -3m- 0.75m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.5.37P: The inclined beam represents a ladder with the Following applied loads: the weight (W) of the house...

See similar textbooks

Similar questions

the homogeneous cylinder of weight W=100 N rests in a frictionless right angled corner. determine the contact forces NA and NB angle is 30 degrees
6-46 A rope and pulley system is used to support a body as shown in Fig. the ropes are continuous over the pulleys. Determine the force P required to hold the body in equilibrium if the mass m of the body is 250 kg. Each pulley is free to rotate, and P
Q3 (5-28) : The articulated crane boom has a weight W and mass center at G. If it supports a load L, determine the force acting at the pin A and the compression in the hydraulic cylinder BC when the boom is in the position shown. Given: W:= 500N L:= 2400N b G a := Im d b:= 0.25m C := 0.25m d := 2m 16.04 Fg- 20.94AN 0 := 40deg 9.835
-1 m 1m Draw a Free-Body Diagram of the bars AD and BC shown in the figure. Assume all 1m 500 N hinges to be smooth and neglect the weight of each bars. 1 m B.
QI (5-22) : The uniform door has a weight W and a center of gravity at G. Determine the reactions at the hinges if the hinge at A supports only a horizontal reaction on the door, whereas the hinge at B exerts both horizontal and vertical reactions. Given: W := 100N a := 0.3m b:= 0.3m 4y - 33.3N c:= 0.05m By= 33.3N d:= 0.2m By = 100N
C6-70 The tower crane shown in Fig. construction materials. The counterweight C weighs 31,000 N; the motor M weighs 4500 N; the weight of the boom AB is 36,000 N and can be considered as acting at point G; and the weight of the tower is 23,000N and can be considered as acting at its midpoint. is used to lift It is desired that the reaction forces at the feet D and E always be greater than 4500 N to ensure that the tower is never in danger of tipping over. Plot Wmax, the max- imum load that can be lifted as a function of the dis- tance x (0
6-41 A 30-lb force P is applied to the brake pedal of an automobile as shown in Fig. applied to the brake cylinder and the reaction at support A. Determine the force Q P 30° 5 in. B 55 in. 4 in.-
Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C by smooth journal bearings. Determine the components of reaction at the bearings if the rod is subjected to the force F. The bearings ar ein proper alignment and exert only force reactions on the rod. F=815m d=1.00m e=1.90 m f=2.20 m 30° 60° B d f 0.75 m
6-75 A 500-lb homogeneous circular plate is supported by three cables as shown in Fig. in the three cables. Determine the tensions TA Tc 9 in. 15 in. 21 in. 15 in. 9 in 21 in. y
- 2. From the loading as shown, at what is fastened bya frictionless pin to a block weighing l0okN as shown in will produce a rotational equilibrium! figure. At vertical wall the Muau= 0.269 while under the block the Mblock= 0.20. Oetermine the force Pneeded to start the moti on to the Exercise No 3 Lab. A uniform bar AB weighing 5OOKN, distance (x) from the left support what are the values of R, and Rz? 4m 2m right. WAFICO KN W500KM bar X=?. 18 KN P: 18KN/M e = 45° A Molock= 0.2 E. 'k block C m FNA 3m RI Rz
3-11 Detormine the forces in cables A and B if block Wof Fig. P3-11 weighs 350 Ib.
Problem Statement Based on Problem 5-87 from the textbook. Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is tramsitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components of reaciotn at the journal bearing C and thrust bearing D. The bearings are in proper alignment and exrt only force reactions on the shaft. 300 mm 250 mm 200 mm 80 mm D 150 mm F3 F1=70N F2=85N F3=50N Theta=38 degrees