4. What are the fields of Environmental Engineering? 5. What is Environmental Resource? Give atleast 5 examples of natural resources. 6. What is the important role of a civil engineer in the field of environmental engineering?

Q: P F 600 mm 2P 2P A E C 400 mm B D - The assembly consists of two 12.05 mm-diameter A992 steel rods…

A: Steel roads AB and CD Length, L1 =400mm Diameter, d1=12.05mm Young's modulus, E = 200GPa…

Q: segment The following figure shows si(t) and s2(t), the speed of two vehicles over a three-mile of a…

A:

Q: A propped cantilever beam XY, with an internal hinge at the middle,is carrying a uniformly…

A: Given data in question  Load 10 kN/m Span 4 m To find out Reaction at X

Q: ation 1: A concrete column, 330 x 330 mm supports an axial compressive load of 1100 kN. Determine…

A:

Q: Situation 4: The bar ABC consists of 2 cylindrical segments with different lengths and…

A: Given Data Cross sectional area of segment-AB (AAB) = 4.7 in2  Find the normal stress in…

Q: A soil layer with a moisture content of 10 percent and a unit weight of 16.5 KN per cubic meter…

A: Question b) Objective: To determine the dry specific weight of the soil (γd,compaction).   Given:…

Q: 3m 6 kN/m A SUNSAROND 3m 3 kN/m 4 m 15 kN B K 3m 2m Fig. 3 20 kN 1.5 m C (pin) 3m 1.5m 3⁰ 6 kN/m 2m

A:

Q: The scale of an aerial photograph is 1 cm = 150 m and the size of the photograph is 20 cm x 20 cm.…

A:

Q: The local municipality wants to use this well (the pumping well) as an irrigation water supply well…

A: Given, Flowrate (Q) = 2000 gal/min or 4.44 cfs Distance (r) = 210 ft  Transmissivity T = 1746.76…

Q: Two springs are used to support the steel truss structure of 2.5 m height shown in the figure. The…

A: Given: Spring 1: (right support) Shear modulus, G1=300+41=341 GPa Spring diameter, d1=20 mm Helical…

Q: Draw stress path for the following loading conditions on p-q diagram. 1) 6 = 6, initially, Δό, > 0,…

A: To draw stress path for loading conditions-

Q: Is the statement below True or False about Unit Hydrograph Theory? Basin outflow resulting from 1.0…

A: Given data in question  Unit hydrograph  1 inch or 1 mm depth To find out  True or false

Q: A simply supported beam ABCDEF of 5 m length and load Fig. Find the deflection and slope at point E…

A:

Q: Problem 2.8 - The 400-kg precast concrete section is hoisted by a vertical force 'T' from a crane.…

A: Given: Weight of concrete section = 400kg Required : Tension in cable

Q: A granular soil with natural unit weight of 15.4 kN/m³, if the relative density is 70%, w 10%, and…

A:

Q: The picture of the graph isn't showing can you please resubmit it?

A: GIVEN: To Calculate: Draw the Graph of GRAIN size distribution curve.

Q: 1. Given the following two aggregate gradations shown in Table 1. plot individually on a semi-log…

A: Note:- “Since you have posted multiple questions, we will provide the solution only to the first…

Q: Two loads of 1000 KN and 2500 KN act on points A and B. point C is placed 5 meters below the…

A: Given: PA = 1000 kN PB = 2500 kN γdry=18 kN/m3 γsat=20 kN/m3

Q: of water for a community of 12000 capita, with an average consum ay. The pump is used to raise water…

A: The given data in the question is: The centrifugal pump operates at a speed of 1150 rpm The pump…

Q: FORCE SYSTEM IV. EQUILIBRIUM OF NON-CONCURRENT Example Problem 2: A 12-ft bar of negligible weight…

A:

Q: A Pelton wheel is to be designed for a pitch diameter of 1 m and jet diameter of 0.1 m. The number…

A: Given- Pitch diameter D=1 m Jet diameter d=0.1 m Number of buckets=?

Q: The uniform beam has a mass of 50 kg per meter of length. Determine the reactions at the supports.…

A:

Q: 5. Given the hydraulic press shown in the figure, calculate the force "P" required to raise a load…

A:

Q: The state of stress at a certain point in a stressed body is shown in figure. The magnitudes of…

A: Given- Stress- σx=100 MPaσy=-100 MPa

Q: For a city of population 200,000 capita and WCav =240 l/c/d the average daily WC as follows: a.…

A: Given: The average daily WC: Time 12-2 AM 2-4 4-6 6-8 8-10 10-12 12-2 2-4 4-6 6-8 8-10 10-12 AM…

Q: Calculate the moment of inertia of around the x-axis a=20mm b=30mm c=30mm d=42mm e=23mm f=10mm

A:

Q: Determine the slope at A and deflection at C in the beam shown below A 12 kN/m !!!! 3 m ↓↓↓↓↓ C 9 KN…

A: Data given Find : Slope at A  Deflection at C

Q: The stopping sight distance (SSD) for a level highway is 140 m for the design speed of 90 km/h. The…

A: Given that:- Stopping sight distance = SSD = 140 m Design speed = V = 90 km/h Acceleration due to…

Q: A saturated soil has saturated unit weight of 21 kN/m³ and Gs='2.69. Find dry unit weight, void…

A:

Q: A column of initial length of 80 m is pinned at its base and restrained against lateral motion at…

A: Given

Q: Two solid rods (1) and (2) of the same material are joined If the normal stress together at flange B…

A: Given Data Permissible normal stress = 275 MN/m2 = 275 N/mm2  E = 60 GN/m2 = 60 × 103 N/mm2  Find…

Q: Water (bulk modulus of elasticity = 2.2 x 103 MPa) is flowing with a velocity of 2 m/s through an…

A:

Q: For a given traverse, latitudes and departures are calculated and it is found that sum of latitudes…

A:

Q: I. Select an example from the list of each Structural Shapes. Copy the properties such as mass,…

A: Given,  Several structural shapes according to their designation   To find : Example of each…

Q: 4 in. 200 kip 3 ft The column is constructed from high-strength concrete and eight A992 steel…

A:

Q: ↓x = bxx = i in.4 in.4

A:

Q: : For the soil profile shown in figure below, determine total and effective vertical stresses and…

A: Given data,  Gs of sand = 2.66 Gs of silt = 2.7 Gs of clay = 2.72  e sand = 0.72 e silt = 0.66 e…

Q: If a point in a strained material is subjected to two mutually perpendicular stresses, 0x = 100 MPa…

A:

Q: The state of stress at a point is given by oxx = 60 Mpa, oyy = 120Mpa and Oxy = 40 MPa. The radius…

A: Given data- State of stress at a point is given- σxx=60 MPa,σyy=120 MPa,σxy=40 MPa, To Find- The…

Q: A 1/2 cubic metre short boom dragline having ideal output of 150 m³/hr is to be used to excavate…

A:

Q: Question A concrete beam of rectangular cross-section of 200 mm x 400 mm is prestressed with a force…

A: Given Cross-section- 200 mm × 400 mm,Force P=400 kN,e=100mm. It is needed to find the maximum…

Q: A wooden buoy (s.g. = 0.62) is 70 mm by 70 mm by 5 m long is made to float in sea water…

A:

Q: or a given sandy soil, the maximum void ratio is 0.72 and the minimum void ratio is 0.46. If the…

A: Relative density=82% Specific gravity=2.68 Water content=11% Max void ratio=0.72 Min void ratio=0.46…

Q: Bond, Anchorage and Development Length Question 1: How much shall be the development length of 25 mm…

A: Given- 25 mm diameter deformed barFe415 steel in tension,Design bond stress in tension=2.24 N/mm2

Q: 3. Rigid member ABD is connected to elastic member CDE as shown. For the given loading, what are the…

A: Given E=70GPa A=100 mm2 To Find Vertical displacement at A and E

Q: A proposed office building will include a 10 ft x10 ft square, 3 ft deep (the footing height is also…

A: Given, Cross sectional area of footing = 10 ft x 10 ft  Depth of footing = 3 ft  Angle of internal…

Q: The yacal beam with 5000 lbs weight is carrying two vertical loads. The beam is supported by a cable…

A:

Q: What is 3.785

A: For the given question determine the purpose of the term 3.785 in the solution.

Q: Question A rectangular column of size 300 mm x 200 mm carries an eccentric load of 200 kN as shown…

A: Given data- A rectangular column- 300 mm × 200 mm,Eccentric load P=200 kN,Minimum stress=0, To Find-…

Q: You have been asked to obtain an object/structure/component that has failed (It may come from your…

A:

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.