4. In the following figure, 4-bit asynchronous UP-COUNTER is given. a) Determine total propagation delay time, if each flip-flop has a propagation delay for 120 ns. b) Determine the maximum clock frequency at which the counter can be operated. c) If clock frequency is 80 KHz, find frequency fo3. HIGH Clock Jo FF-0 > CLK Ko Qo Qo J₁ FF-1 > CLK K₁ Q₁ Q₁ J₂ K₂ FF-2 CLK Q₂ Q₂ J3 FF-3 ▶ CLK K3 Q3 Q₁ b

4. In the following figure, 4-bit asynchronous UP-COUNTER is given. a) Determine total propagation delay time, if each flip-flop has a propagation delay for 120 ns. b) Determine the maximum clock frequency at which the counter can be operated. c) If clock frequency is 80 KHz, find frequency fo3. HIGH Clock Jo FF-0 > CLK Ko Qo Qo J₁ FF-1 > CLK K₁ Q₁ Q₁ J₂ K₂ FF-2 CLK Q₂ Q₂ J3 FF-3 ▶ CLK K3 Q3 Q₁ b

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) 1/6 Pat DigClock Part List OFFTIME = SuS DSTM1 ONTIME = DELAY= STARTVAL = 0 OPPVAL = 1 Sus EUK FleStim AC Lbrajes Design Cache b) Read the specification of 74LS47 (BCD-to-7-Segment Decoder shown in Appendix) to see how the logic IC operates to drive a 7-segment LED display. Draw the circuit connection of the decade counter in (a) and the decoder to display the count value on the 7-segment LED display. Further explain why common anode…
Determine the total time required to serially transfer the eight bits contained in waveform A of Figure the first to be transferred. The 1 MHz clock is used as reference. and indicate the sequence of bits. The left-most bit is Clock A
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate thecomplete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform.(Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.)(Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)
9. Analysis of Synchronous Counters, in the following figure, write the logic equation for each input of each flip-flop. Determine the next state for state 010,011,100,111 as Q2Q1Q0 sequence. FF0 FFI FF2 Ko K, K2 CLK
(c) For each of the following parts, fill in the respective row of the timing diagram shown in Figure 5. (i) Find the input for a rising-edge-triggered D flip-flop that would produce the output Q as shown in Figure 5. (ii) Find the input for a rising-edge-triggered T flip-flop that would produce the output Q as shown in Figure 5. Clock D Figure 5
2- Using JK Flip flops, a 2-bit counter will be designed that will count down ((11-10-01-00) when the input is "0") and the random sequence given when the input is "1" (00-01-11-10). a) Construct the state table for the sequential circuit. b) Obtain the simplified input equations for flip-flops. c) Draw the logic circuit for the 2-bit counter.
Discussion 1. For a master-slave J- K Flip - Flop with the inputs below, sketch the Q output waveform. Assume Q is initially low. Assume the Flip - Flop accepts data at the positive-going edge of the clock pulse. 2. The following serial data stream is to be generated using a J-K positive edge-triggered Flip – Flop. Determine the inputs required. 101110010010111001000111. 3. By using J- K flip/flop from RS Flip - Flop use block diagram and other gates. 4. a- what are the application of Flip - Flop. b- What is the difference between the Flip - Flop circuit and the other combinational logic eircuits?
Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
Q#01: The schematic shown in figure below is for Divide_by_11, a frequency divider, that divides clk by 11 and asserts its output for one cycle. The unit consists of a chain toggle-type flip-flops with additional logic to form an output pulse every 11th pulse of clk. The asynchronous signal rst is active-low and drives Q to 1. Develop and verify a model of Divide_by_11. Vcc 20LSB Q2 03MSB clk clk clk clk clk rst rst rst rst wl w2 clk QB cik_by_11 rst rst
Obtain the state diagram for the following state machine. Consider that the flip flop above is the MSB.
Q.6 Given a sequential circuit implemented using two JK flip-flop as in Figure Q.6a. Analyse the circuit by completing the timing waveform given in Figure Q.6b. QA QB Vcc SET SET J K CLR Q K CLR CLEAR Clk Figure Q.6a Clk CLEAR QA Qs Figure Q.6b
Please help me out. Details are very much appreciated. Latch Flip-flop – Refer to the Waveform number 1. Assuming the initial state is Q = 1, draw the waveform of Q.