4. Consider the circuit shown in the following Figure. The cut-in voltage of each diode is VDO = 0.7 V. Let v₁ = (5+last digit of your IDX10²) V. Assume both diodes are conducting. Is this a correct assumption? Why or why not? Determine IR₁, ID₁, D2, and vo (if necessary, modify the assumption and calculate the values for the correct one). R = 1.7 kΩ D₁ IDI VB = 1 V TIF ID2. www + D₂ VO R₂= 4 ΚΩ [16]

4. Consider the circuit shown in the following Figure. The cut-in voltage of each diode is VDO = 0.7 V. Let v₁ = (5+last digit of your IDX10²) V. Assume both diodes are conducting. Is this a correct assumption? Why or why not? Determine IR₁, ID₁, D2, and vo (if necessary, modify the assumption and calculate the values for the correct one). R = 1.7 kΩ D₁ IDI VB = 1 V TIF ID2. www + D₂ VO R₂= 4 ΚΩ [16]

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
True or False. Please explain. thank you As the temperature increases, the forward voltage decreases in a silicon diode. Then, the graph of the forward bias region will shift to the left.
Sketch i agains v to scale for the circuit. Assume 0.6 V for all diodes in the forward-bias region.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Determine the current I in the circuit (i). Assume the diodes to be of silicon and forward resistance of diodes to be zero.