4. Compute for the Nusselt value of a forced convection through an elliptical duct at constant Ts, where a/b=8. The temperature of the fluid at the inlet is higher than at the exit. Flow is fully developed with Re = 33,370 and Pr = 0.693

4. Compute for the Nusselt value of a forced convection through an elliptical duct at constant Ts, where a/b=8. The temperature of the fluid at the inlet is higher than at the exit. Flow is fully developed with Re = 33,370 and Pr = 0.693

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Related questions

Q: Water flows through a tube of length L with a mean inlet temperature (T;). The tube is held at a…

A: Heat flow will increase. This can be explained with the concept of internal forced convection.

Q: Consider two cases involving parallel flow of dry air at V = 3.5 m/s, T = 45°C, and atmospheric…

A: The thermal boundary layer is the flow zone over the surface where temperature change in the…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A: Given details: h1=3212 kj/kgV1=237 km/hrh2=2556 kj/kgA1=0.22 m2sp.volume=0.32 m3/kg

Q: Q4) Water at the rate of 0.6 kg/s is forced through a smooth (3cm)-ID tube 16 m long.The inlet water…

Q: Question 6: Air is to be cooled in the evaporator section of a refrigerator by passing it over a…

Q: 33. Water at 25 C flows in a smooth tube, having a diameter of 5 cm, at a rate of 1 kg/s. The tube…

Q: Write your answer in 4 decimal places. DO NOT round off intermediate values. Water at a mean…

A: As per given question Temperature =25°c Re=10000 We have determine Nu and heat convetion cofficien

Q: Q2-A tube bank uses an aligned arrangement of 30 mm diameter tubes with S = S= 50 mm and a tube…

Q: Consider two cases involving parallel flow of dry air at V = 5 m/s, T=45°C, and atmospheric pressure…

Q: ir is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8…

Q: 2- To solve these problems, refer to notes on Blackboard about convection inside pipes. Also, assume…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 1. The mean Nusselt number for fully developed laminar flow in a circular tube under constant heat…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Consider two cases involving parallel flow of dry air at V = 3 m/s, T = 45°C, and atmospheric…

Q: Hydrogen (viscosity = 0.009 centipoise) is pump from a reservoir at 2x10³ kPa pressure through a…

A: Given DataP1=2.6×103kPaP2=2×103kPad=50mmL=500m **In Question there is no demand of any terms for…

Q: For internal flow with fully developed flow condition The velocity profile ....................…

A: In the entry region during internal flow, velocity profile and thermal profile change in the…

Q: A liquid is entering a 10 m long pipe of 0.2 m diameter at 25°C with an average velocity of 0.02…

Q: Consider two cases involving parallel flow of dry air at V = 4.5 m/s, T = 45°C, and atmospheric…

Q: Water at 15.6 °C flows across a 20- cm-square plate with a velocity of 2 m/s. A thin strip, 5 mm…

A: This question is solved with the help of the law of convection. It states that heat transfer by…

Q: An electronic device is cooled by water flowing through capillary holes drilled in the casing as…

A: Given,temperature of device = 353Kcapillary holes = 0.3mdiameter = 2.54x10-3mwater enters at a temp…

Q: Water with an average temperature of 35 °C flows in a pipe of 3 mm diameter and 2 m length. The pipe…

A: Write the values of kinematic viscosity, Prandtl number, and Thermal conductivity of water at 35oC…

Q: A 10 m long thin-walled stainless steel tube of diameter 15 mm is used to sterilize pharmaceutical…

Q: Engine oil enters a circular tube D=6-cm in diameter and L=29-m in length. If the flow rate and…

Q: An isothermal silicon chip of width W = 20 mm on a side is soldered to an aluminum heat sink (k =…

A: Data given- Lf = 15 mm W = 20 mm K = 180 W/m-K N = 11 t = 0.182 mm S = 1.982 mm Tair = 20°C…

Q: In an oil Coolerpo.08 o hot oil enters a drameter Bo . An equal mass of cooling water flows through…

A: mo =Mass flow rate of oil =0.08kg/s mw =Mass flow rate of water= mo T1 =Temperature of oil entering…

Q: A stream of air flows over a pipe with an outside diameter of 9 cm. The temperature at the surface…

A: First calculate the Reynold number to identify the flow condition

Q: A boiling-water nuclear reactor vessel comprises a cylinder of length 20 m and diameter 5 m with…

A: Given that, Length of cylinder, L=20 m,Diameter of hemispherical end, d=5 m,Power generated, Q˙=1800…

Q: 8. A lead pipe has 2 cm inside diameter, 3 cm outer diameter, length of 130 cm. Liquid water at 4°C…

Q: 3 Water at 15°C (p = 999.1 kg/m , cp = 4.18 kJ/kg.K and u = 1.138E-3 kg/m.s k = 0.631 W/m.°C) is…

Q: You are designing an IC heatsink which uses round pins in cross-flow. The heatsink must dissipate…

Q: Numerical investigation of heat transfer and fluid characteristics for flow though a corrugated tube…

A: Please find the solution below

Q: For seaworthiness trial of a new ocean-going vessel design, the total convective heat transfer rate…

Q: At an average temperature of 110°C, hot air flows through a 5 m pipe with outside diameter of 80 mm…

Q: Air at 15 m/s is cooled from 80 C to 60 C in 2.5cm diameter tube. The tube wall is maintained at a…

Q: Air that is fully-developed flows in a rectangular duct of inside dimensions 0.610 m x 0.305 m. The…

A: given, we have h=0.610m b=0.303 m L=2.44 m τmi=21.1°CTm.0 =26.7°Cm=2.72 kg/n

Q: Q1. Three types of pin fins. The fins will be subjected to a gas in cross flow at v= 10 m/s. The…

A: Given dataVelcoity v = 10m/secDiameter D = 20mm = 0.02mTemperature of air T = 350KProperties of air…

Q: Choose the right answer 1. The mean Nusselt number for fully developed laminar flow in a circular…

Q: A 2-cm diameter, 10-m long tube transports water at an average flow velocity of 8 m/s. The water…

A: Nusselt number is , based on Reynolds number and prandtal number. and these number are based on the…

Q: JAn electronic device is cooled by water flowing through capillary holes drilled in the casing. The…

Q: What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate…

A: here, for constant temperature of plate have specific condition where nusselt number will be…

Q: What is the required tube length if the coolant is air and its velocity is V = 20 m/s

Q: Write your answer in 4 decimal places. DO NOT round off intermediate values. Water at a mean…

Q: sliding. The sliding velocity is 6m/s and the bearing is s thickness is always three times the…

Q: Air at 300 kPa and an average of 450 K is being heated as it flows through a rectangular conduit of…

Q: flowing with water at temperatures of 30 ^o C and 40 ^o C. Calculate the maximum velocity under…

Q: A cylinder 1 inch in diameter is placed in a hot water pipe at right angles to the direction of the…

A: Write the given data with suitable variables: d=1 in=0.0254 mT∞=80 °FT=100 °Fm.=2705 lb/hr=0.34 kg/s

Q: A Figure illustrates the tube-flow system. The heat transfer under developed flow conditions when…

Question

100%

4. Compute for the Nusselt value of a forced convection through an elliptical duct at
constant Ts, where a/b=8. The temperature of the fluid at the inlet is higher than at
the exit. Flow is fully developed with Re = 33,370 and Pr = 0.693

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

H.W5) A Figure illustrates the tube-flow system. The heat transfer under developed flow conditions when the flow remains laminar. The wall temperature is Tw, the center of the tube temperature is Te the radius of the tube is r., and the velocity at the center of the tube is uo. The velocity distribution equation is: =1 - ио Prove that: 1 aT uor, T- T= а дх 4 Start the solution of the equation : P(2ar drjuc,T 1 a aT 1 әт %3D ur дr ar a dx
) A 75 mm-diameter orifice is on the verticalside of a closed tank. The tank rests on a flat groundand the orifice is 0.5 m above the ground. Filled withfour fluids with air on the topmost portion that is undera pressure of 15 KPa, and the rest of specific gravities of0.80, 1.0, and 1.50, respectively, the jet hits the groundat a horizontal distance of 3.75 m. If the liquids have thesame thickness, and the power lost in the system is 233watts, determine the following:(a) The initial discharge in L/s if C=0.63.(b) The thickness of each liquid in m.(c) The coefficient of contraction.
An engineer who took college fluid mechanics on apass-fail basis has placed the static pressure hole farupstream of the stagnation probe, as in Fig, thuscontaminating the pitot measurement ridiculously withpipe friction losses. If the pipe flow is air at 20°C and1 atm and the manometer fluid is Meriam red oil (SG =0.827), estimate the air centerline velocity for the givenmanometer reading of 16 cm. Assume a smooth-walledtube.
Derive the Continuity Equation by considering a stream-tube of flow through a conduit.
(1) Given the working form of the Bernoulli equation as dW - F dm Where 5 is the friction heating per unit mass dQ F = Au dm Given also that friction heating in laminar flow of Newtonian fluids in circular pipes is given as -AP F = = -gAz = Q Ax u 128 Ax is change in the x-direction. A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometer
Jet water in pipe with diameter equal to 50 moving to velocity 30 divided into two branches with (0.75Q) and the other with (0.25Q) recpectively and Un equal diameter compnte value of force compenents on the plane
You are designing an IC heatsink which uses round pins in cross-flow. The heatsink must dissipate 3000W. The heatsink has 10 rows of 8 columns of round pins with a diameter of 1mm. The pins have longitudinal and transverse pitch of 6mm. The incoming air is at 25oC with a velocity of 3 m/s. Assume fluid properties are constant. If the pins are arranged in-line: a) Find the Reynold’s Number b) Find the Nusselt Number c) If the pins are 30mm tall, how hot must the pin surface be (average) to dissipate the proper amount of heat?
The velocity profile for laminar flow between two plates, as in Fig.3, is 2umaxy(h-y) h4 u= If the wall temperature is Tw at both walls, use the incompressible flow energy equation to solve for the temperature distribution T (y) between the walls for steady flow. Energy equation: dT pcp dt y=h y=0 •= kV²T +4 u(y) v=W=0 Tw T(y) Fig.3. Fluid flow between two walls
Air is flowing in a duct with velocity of 7.62 m/s and static pressure of 2.7 cmWG. The duct diameter is 1.22 m and the barometric pressure is 99.4 kPa and the gage fluid temperature and air temperature is 30 degC. What is the total pressure against which the fan will operate in mm of water? and What is the required motor brake power in Question no. 4 assuming a mechanical efficiency of 89%.
Consider the incompressible-fluid-flow problem in the 1 D porous body shown in the figure. Obtain the necessary system of equations to solve the pressure distribution in the system in steady state condition. Production Rate,4sc , STB/D No-Flow Boundary ap a psi/t 1 2 3 Ax
A 1-in-diameter (D = 1 inch) rotating machined shaft has a groove 0.1-in deep with a 0.1-in radius machined into it. The shaft is subjected to a pulsating (i.e. R = 0) torque and bending moment of following values. Based on laboratory experiments at 550°F, Sut = 150 ksi, Sy = 120 ksi, and S'e = 90 ksi are measured. Using mod-Goodman equation and for operating temperature of 550°F and 90% reliability, determine the factor of safety for yielding and fatigue of this shaft. Tmax = 2000 Ib-in Mmax = 1600 lb-in Mmin = -1200 Ib-in D - -d- M T M T
5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .