4. An F-14 Tomcat fighter plane, at rest on an aircraft carrier, has a mass of 34,000 kgs. The plane is pushed across the aircraft carrier, which is 330 m long, so that it reaches a take off speed of 70 m/s. a) What is the kinetic energy of the plane as it takes off? b) How much force is needed to push the plane across the aircraft carrier so that it reaches its take off speed?

4. An F-14 Tomcat fighter plane, at rest on an aircraft carrier, has a mass of 34,000 kgs. The plane is pushed across the aircraft carrier, which is 330 m long, so that it reaches a take off speed of 70 m/s. a) What is the kinetic energy of the plane as it takes off? b) How much force is needed to push the plane across the aircraft carrier so that it reaches its take off speed?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pile drivers are heavy, metal hammer used to drive posts into the ground when constructing a building. One such pile driver with a mass of 200 kg was lifted 3 meters above the ground then released, driving a beam 8 cm into the ground. What is the speed and exerted force of the pile driver if a 60-N frictional force is exerted by the guide rails on the pile driver.
2).A 5.18 g bullet moving at 672 m/s strikes a 715g wooden block at rest on a frictionless surface. The bullet emerges with its speed reduced to 428m/s. Find the resulting speed of the block.
A 3-meter-long 25 kg beam is supported by two cables as shown below. You can treat the beam as a slender rod. Assume we want the left end of the beam at A to remain as a constant height while the right end of the beam at B to accelerate upwards at a rate of 1 m/s?. a) What is the rate of acceleration of the center of the beam and the rate of angular acceleration for the beam? b) What will T, and T2 need to be to achieve these accelerations? T A .5 m 1.5 m 1m B.
An airplane, flying with a tail wind, travels 1200 miles in 2 hours. The return trip, against the wind, takes 2 1/2 hours. Find the cruising speed of the plane and the speed of the wind (assume that both rates are constant).
A toy boat slides down a frictionless track and around a circular loop as shown in the diagram below. A C B D The boat slid around the vertical circle and at point C its speed was 2.6 ms-1. The mass of the boat is 150 g and the radius of the circular loop is 14 cm. a. Find the magnitude of the weight of the boat. b. Find the magnitude of the centripetal force on the boat as it moves past point C. c. Hence, find the normal force the track applies to the boat as it moves past point C.
A body weighs 1000 lbf when exposed to a standard earth gravity ? = 32.174 ??/?². (a) What is its mass in kg? (b) What will the weight of this body be in N if it is exposed to the moon’s standard acceleration ?moon = 1.62 ?/?²? (c) How fast will the body accelerate if a net force of 400 lbf is applied to it on the moon or on the earth? The answers are (A) 454kg (B) 735N (C) 3.92 m/s² (ALL I NEED IS A SOLUTION. THANK YOU) (Our subject is FLUID MECHANIC)
There is a system including two blocks. (mĄ = 2kg, mg = 8kg) This system starts movement from the rest (block B is going downward). If kinetic coefficient of friction for the surface is 0.4. A) What is the tension in the cable? B) If block B travels 0.7 m downward, what is its velocity? A В 0 = 60° %3D
The vehicle shown starts from rest at the bottom of the hill and accelerates up the hill due to the force FR from the road. Note that this is a static friction force and is not dissipative. Vrop = 9.7 m/s m = 1600 kg h = 50 m FR = 7300 N 0 = 25° A) If the vehicle reaches the top of the hill with the speed shown, how much thermal energy is dissipated in the process? B) Assuming that air drag, Fang , is the only dissipative force during this process, try to estimate the cross-sectional area of the vehicle "seen" by the air. In the formula for air drag, regard the car's speed as being a constant v = 5.0 m/s (this speed is roughly half of the starting and ending speeds). Use C = 0.5 for the drag coefficient and p = 1.25 kg/m³ for air density.
There is a 1.3 kg box moving along a horizontal frictionless floor with a velocity of 5.0 m/s. After traveling 2.0 meters it presses against a spring with spring constant 12.5 N/m. By how much will the spring be compressed when the block is at rest? a) How much energy does the system have initially? b) By how much will the spring be compressed when the block is at rest c) If instead of a frictionless surface, a section of the (0.5 meters) floor was replaced by a rougher surface that resulted in a coefficient of friction of 0.3 between the box and the surface. How much work would be done on the block when it travels over this rough surface?
Two rods, with masses MA and MB having a coefficient of restitution, e, move along a common line on a surface, figure 2. a) Find the general expression for the velocities of the two rods after impact. b) IfmA =2kg,mB =1kg,vB=3m/s,ande=0.65,find the value of the initial velocity vA of rod A for it to be at rest after the impact and the final velocity v’B of rod B. c) Find the percent decrease in kinetic energy which corresponds to the impact in part b
A body weighs 1000 lbf when exposed to a standard earth gravity ? = 32.174 ft/s². (a) What is its mass in kg? (b) What will the weight of this body be in N if it is exposed to the moon’s standard acceleration ?moon = 1.62 m/s²? (c) How fast will the body accelerate if a net force of 400 lbf is applied to it on the moon or on the earth? The answers are (a) 454kg (b) 735 N (c) 3.92m/s² (Our subject is FLUID MECHANIC, all I need is a clear solution) thank you
2. An 8.00 kg package in a mail-sorting room slides 2.00 m down a chute that is inclined at 53.0° below the horizontal. The coefficient of kinetic friction between the package and the chute's surface is 0.40. a) Calculate the net work done on the package by summing the work done on the package by friction, gravity and the normal force. b) If the package has speed of 1.2 m/s at the top of the chute, what is its speed at the bottom?