4 of 21Which A/C electronic control system component does the ECM (controller) receive input from?SensorsCompressor relayBlower fan moduleLow pressure switch5 of 21What should be involved in the inspection of an actuator?O Lateral runoutTemperature sensor feedbackO LubricationFreedom of movement6 of 21When inspecting the air conditioning electronic control system, technicians should:O Inspect the metering deviceInspect the engine coolant levelsInspect the evaporatorInspect the condenser

4 of 21 Which A/C electronic control system component does the ECM (controller) receive input from? Sensors Compressor relay Blower fan module O Low pressure switch 5 of 21 What should be involved in the inspection of an actuator? O Lateral runout Temperature sensor feedback Lubrication Freedom of movement 6 of 21 When inspecting the air conditioning electronic control system, technicians should: Inspect the metering device Inspect the engine coolant levels Inspect the evaporator Inspect the condenser

4 of 21 Which A/C electronic control system component does the ECM (controller) receive input from? Sensors Compressor relay Blower fan module O Low pressure switch 5 of 21 What should be involved in the inspection of an actuator? O Lateral runout Temperature sensor feedback Lubrication Freedom of movement 6 of 21 When inspecting the air conditioning electronic control system, technicians should: Inspect the metering device Inspect the engine coolant levels Inspect the evaporator Inspect the condenser

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter18: Troubleshooting Modern Refrigeration, Heating, And Air-conditioning Control Circuitry And Systems

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Similar questions

The figure below shows the closed loop position control block diagram of a spring mass damper system. Based on this figure , answer the following questions (13-21) 13. Block number 3 represents.. . function * ...transfer 6 20s+50 2 2s $2+8s+4 (4) (5) (1) (2) (3) 10 Position Sensor Controller Process O Actuator
Industrial Motor Controls 8.a. A typical motor speed control circuit that is controlled by an analog current loop will have a current ofA. 4-20 mA.B. 2-20 mA.C. 5-50 mA.D. 0-10 mA.8.b. Which one of the following statements is true of a disabled contact or coil?A. The disabled element has been automatically disabled due to module failure.B. The disabled element is held false by the PLC.C. A disabled contact or coil is caused by a faulty memory location in the PLC.D. A contact must be in the disabled state before it can be forced ON or OFF.
20.a. A capacitive sensor is used to detect the presence of _______ objects.A. ferrousB. nonmovingC. nonconductiveD. magnetic20.b. A three-phase motor can be made to run backwards byA. connecting a resistor in series with the armature.B. reversing the control voltage connections.C. reversing three of its power leads.D. reversing two of its power leads.
Explain (i) control relay and (ii) Thermal overload relay? please dont copy
Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or B
8. What instruction would you select for each of the following discrete input field devices to accomplish the desired task? (State the reason for your answer.) a. Turn on a light when a conveyor motor is running in reverse. The input field device is a set of con- tacts on the conveyor start relay that close when the motor is running forward and open when it is running in reverse. b. When a pushbutton is pressed, it operates a so- lenoid. The input field device is a normally open pushbutton. c. Stop a motor from running when a pushbutton is pressed. The input field device is a normally closed pushbutton. d. When a limit switch is closed, it triggers an instruc- tion ON. The input field device is a limit switch that stores a 1 in a data table bit when closed.
13.a. A control system that doesn’t return position or velocity information from the motor back to the controlsystem is called a/anA. differential system.B. translated position system.C. directional system.D. open-loop system.13.b. You’re looking at a tachometer feedback signal on an oscilloscope. The waveform takes a long time togo to zero volts. This means that the system isA. critically dampened.B. at high speed.C. reversing direction.D. overdampened.
What is synchro? Explain how it is controlled with respect to control system
Explain with the aid of a drawing or hand sketch how a bimetallic overload relay operates?
H.W: What instruction would you select for each of the following discrete input field devices to accomplish the desired task? (State the reason for your answer.) a. Turn on a light when a conveyor motor is running in reverse. The input field device is a set of contacts on the conveyor start relay that close when the motor is running forward and open when it is running in reverse. b. When a pushbutton is pressed, it operates a solenoid. The input field device is a normally open pushbutton. c. Stop a motor from running when a pushbutton is pressed. The input field device is a normally closed pushbutton. 33
control system answer pleasae as soon as possible
Consider the block diagram shown is for a closed-loop temperature control system. Where is the setpoint?