4) In the temperature range from 600°C to 750°C, a steel wire with 100 mm length shows thesteady state creep behavior. The wire was exposed to 600°C under 300 MPa for ten years, howlong the specimen would be? (TH Trung TrongStress (MPa)1000 FTTinh Tru Trung Trung Trong th800600400200100806040815 C20 d10-610410-5650 C730 C925°Cd d d d d10-3 10-2 10-1 11010²Steady-state creep rate (h-¹)10³

Answered: Image /qna-images/answer/cc043be6-a146-4a18-b2ac-a98170c1aefd.jpg

4) In the temperature range from 600°C to 750°C, a steel wire with 100 mm length shows the steady state creep behavior. The wire was exposed to 600°C under 300 MPa for ten years, how long the specimen would be? ( truy Tro trong trung trong trong Tru Stress (MPa) 1000 800 600 400 200 100 80 60 40 815 C 20 106 105 104 650°C 730 C 925 C and cond 10-3 10-2 10-1 1 Steady-state creep rate (h-1) 10 10² 10³

4) In the temperature range from 600°C to 750°C, a steel wire with 100 mm length shows the steady state creep behavior. The wire was exposed to 600°C under 300 MPa for ten years, how long the specimen would be? ( truy Tro trong trung trong trong Tru Stress (MPa) 1000 800 600 400 200 100 80 60 40 815 C 20 106 105 104 650°C 730 C 925 C and cond 10-3 10-2 10-1 1 Steady-state creep rate (h-1) 10 10² 10³

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The tensile strength of copper alloy C71500-H80(copper-30%Ni) has been measured at 580 MPa. Estimateupper and lower bounds for the endurance limit at 108 cyclesfor this alloy.
(7) A copper rod is 8 m long at 20°C and has a coefficient of linear expansion a = 17 x 10-6 (C°)-!. What is the increase in the rod's length when it is heated to 40 °C?
A round billet made of copper was extruded at a temperature of 500C0 the billet diameter was 100 mm, and the final extruded (hollow )shape and dimensions are shown in the figure. Estruson constant k for varoun metals at deferent termperatures 1200 1400 estimate the extrusion force iequired. "C 800 1000 600 400 80 Stainless steel Beryllium 400 60 70-30 Brass Cold-rolled Соpper 200 40 steel 20 1100 Aluminum 2500 2000 1500 1000 Temperature ("F) В Chromium Molybdenum Extrusion constant, k (10° psi) MPa
knowing that the room temperature is 30 C the thermal expansion coefficient is 1.5*10^-0.5 the material is cast alloy steel. . Estimate theoretically the expansion and contraction if cylinder heated to (40??) and if cooled to (5??)
(a) Borosilicate glass bottles are processed into bottles using press and blow method shown Temperature ("F) in Figure 6(a). By referring to Figure 6(b), 400 800 1200 1600 2000 2400 2800 3200 1018 1016 Borosilicate i. State the suitable temperature range for making glass bottles and justify the glass 96% silica Fused 1016 glass silica 1014 Strain point answer. 1014 1012 Annealing point 1012 1010 H1010 ii. Discuss the process to relieve thermal stresses the glass bottles using Figure 6(b). 10 Softening point 10 106 Working range 105 10 i1i. Briefly discuss the consequence if the process in (ii) is not performed on the glass Working point 10 10 bottles. Melting point 102 Soda-lime glass 200 400 600 800 1000 1200 1400 1600 1800 Temperature ("C) iv. State THREE (3) reasons why glass would be the best material for the glass (a) (b) bottles? Figure 6. (a) Press and blow method and (b) temperature dependence of viscosity for various types of glasses Viscosity (Pa-s) Viscosity (P)
Stress (MPa) 500 400 Consider the brass alloy for which the stress-strain behavior is shown in the Animated Figure 7.12. A cylindrical specimen of this material 9.9mm (0.3898 in.) in diameter and 98.8mm (3.890 in.) long is pulled in tension with a force of 9780N(2199/b). If it is known that this alloy has a value for Poisson's ratio of 0.35, compute (a) the specimen elongation, (b) the reduction in specimen diameter. Note: because the diameter decreases, enter a minus sign in your answer. Tensile strength 450 MPa (65,000 psi), Strain =0 Stress = 0 MPA Stress =0 psi 70 Strain = 0 Stress 0 MPA 60 Stress = 0 psi 103 psi 50 40 MPa Yield strength 300 250 MPa (36,000 psi) 40 30 200 200 20 100 10 100 0 0 T 10 P 0.10 0.20 Strain 10.065 0 0.30 0.40 30 20 10 Stress (10 psi)
Can you represent strain as a function of time using the Maxwell Viscoelastic Model.
An aluminium roofing sheet on a particular building was making a cracking noise at temperature of 60oC. The sheet have an initial length of 3m long at room temperature. How long have the aluminium sheet been expanded to be causing that cracking noise. NB: Take the coefficient of expansivity of the sheet to be 24x10-6.
Blank 1 materials, which behave in a manner similar to Newtonian ﬂuids under time-invariant conditions but, if the shear stress changes suddenly,behave as if plastic.
The compressive strength of alumina quartz (Al2O3) is 2.1 GPa. A quartz tube is being used for a vacuum furnace. Both ends of the tube are constrained and cannot move. To what temperature can the tube be heated up from room temperature such that the tube won’t fracture due to the thermal stress?
4) Express very briefly why the first region (Primary Creep) in Strain-Time creep diagram can be a design limitation (for what type of applications in general? Please DO NOT write aircraft parts!).: 5) For what type pf applications secondary creep range in Strain-Time creep diagram can be considered as design range?:
Mechanical Engineering Consider two polycrystalline samples with grain size of 0.25 and 5 um. Cooling of the materials produces cracks due to the thermal expansion mismatch. The approximate dimensions are similar to the grain-boundary facets. Determine the tensile strength of the two materials if both have Kiç as 3.5 MN m0.3. Which sample would you use for your project that requires high strength? (geometric factor is unknown)