333: E8B3 8B3: 0A12 A12: 2153 Since the contents of the relevant addresses are 333 in the basic computer given above, the initial value of the PC is 333; When fetching and executing an indirectly addressing ISZ instruction, write the contents of the following registers in hexadecimal (hex) format for the T5 time. AR ........... DR......... IR ........... PC ...........

333: E8B3 8B3: 0A12 A12: 2153 Since the contents of the relevant addresses are 333 in the basic computer given above, the initial value of the PC is 333; When fetching and executing an indirectly addressing ISZ instruction, write the contents of the following registers in hexadecimal (hex) format for the T5 time. AR ........... DR......... IR ........... PC ...........

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 15VE: A(n) ________________ instruction always alters the instruction execution sequence. A(n)...

See similar textbooks

Similar questions

A(n) __________ is a storage location implemented in the CPU.
The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
The contents of a memory location are copied to a register while performing a(n) __________________ operation.
Most Intel CPUs use the __________, in which each memory address is represented by two integers.
A(n) ____________________ instruction copies data from one memory location to another.
Computer Science A computer uses a memory of 64K words with 16 bits in each word.It has the following registers: PC, AR, TR, AC, DR and IRA memory-reference instruction consists of two words: an 16-bit operation-code(one word) and an address field (in the next word).a-List the sequence of microoperations for fetching a memory reference instructionand then placing the operand in DR. Start from timing signal To.b-Design the logic control gates arrangement to perform the fetch instructions.
Q: Compute the physical address for the specified operand in each of the following instructions. The register contents and variable are as follows: (CS)=D0A00H, (DS)=OBOOH, (SS)=0DO0H, (SI)=OFFOH, (DI)=00BOH, (BP)=00EAH and (IP)=0000H, LIST=D00FOH, AX=4020H, BX=2500H. 1) Destination operand of the instruction MOV LIST (BP+DI], AX 2) Source operand of the instruction MOV CL, [BX+200H] 3) Destination operand of the instruction MOV [DI+6400H] , DX 4) Source operand of the instruction MOV AL, [BP+SI-400H] 5) Destination operand of the instruction MOV (DI+SP] , AX Source operand of the instruction MOV CL, [SP+200H] 7) Destination operand of the instruction MOV [BX+DI+640O0H], CX 8) Source operand of the instruction MOV AL , [BP- 0200H] 9) Destination operand of the instruction MOV [SI] , AX 10) Destination operand of the instruction MOV [BX][DI]+0400H,AL 11) Source operand of the instruction MOV AX, [BP+200H] 12) Source operand of the instruction MOV AL, [SI-0100H] 13) Destination operand…
Q: Compute the physical address for the specified operand in each of the following instructions. The register contents and variable are as follows: (CS)=0A00H, (DS)=0B00H, (SS)=0D00H, (SI)=OFFOH, (DI)=00BOH, (BP)=00EAH and (IP)=00O0H, LIST=00FOH, AX=4020H, BX=2500H. 1) Destination operand of the instruction MOV LIST [BP+DI] , AX 2) Source operand of the instruction MOV CL, [BX+200H] 3) Destination operand of the instruction MOV [DI+6400H] , DX 4) Source operand of the instruction MOV AL, [BP+SI-400H] 5) Destination operand of the instruction MOV [DI+SP] , AX 6) Source operand of the instruction MOV CL, [SP+200H] 7) Destination operand of the instruction MOV [BX+DI+6400H] , CX 8) Source operand of the instruction MOV AL , [BP- 0200H] 9) Destination operand of the instruction MOV [SI] , AX 10) Destination operand of the instruction MOV [BX][DI]+0400H,AL 11) Source operand of the instruction MOV AX, [BP+200H] 12) Source operand of the instruction MOV AL, [SI-0100H] 13) Destination operand…
Assembly Programming Write a BC assembly subroutine which counts the 1's in a 16-bit number. You can pass the number to the subroutine via a register or memory. Then, the subroutine returns the result via a register or memory. Some useful hints: For this assignment, you will need to use the circulate/rotate instruction in the BC to scan the bits of the number bit by bit, and then use the SZE to increment the counter or not. Of course, your submission should also have the main program which calls the subroutine. Write enough comments to explain your code. You need to submit only the assembly file which contains the code with the comments.
Q:Non-Volatile Memory includes PROM (Programmable ROM) ROM (Read only Memory) EPROM (Erasable PROM) EEPROM (Electrically Erasable PROM) O RAM(Random access memory) Q: what is the addressing mode for the following instruction: LOAD (ABOO), Ri. * Register Mode Register Addressing Mode Immediate Mode Indexed Addressing Mode indirect mode direct mode
Q: Compute the physical address for the specified operand in each of the following instructions. The register contents and variable are as follows: (CS)=0A00H, (DS)=0BO0H, (SS)=OD00H, (S)-OFFOH, (DI)-вон, (ВР)-00EАН and (IP)-0000H, LIST-0OFOH, АХ-4020H, Вх-2500H. 1) Destination operand of the instruction MOV LIST (BP+DI] , AX 2) Source operand of the instruction MOV CL, [BX+200H] 3) Destination operand of the instruction MOV [DI+6400H], Dх 4) Source operand of the instruction MOV AL, (BP+SI-400H] 5) Destination operand of the instruction MOV (DI+SP] , AX 6) Source operand of the instruction MOV CL, [SP+20OH] 7) Destination operand of the instruction MOV [BX+DI+6400H] , CX 8) Source operand of the instruction MOV AL, [BP- 0200H] 9) Destination operand of the instruction MOV [SI) , AX 10) Destination operand of the instruction MOV (BX][DI]+0400H,AL 11) Source operand of the instruction MOV AX, [ВP+20он] 12) Source operand of the instruction MOV AL, (SI-0100H] 13) Destination operand of…
BX=FFFF, after instruction INC BX is executed, CF ||