Three-Segment PiecewiseLinear Incremental Heat Rat...3.2 Dispatch with Three-Segment Piecewise Linear Incremental Heat RateFunctionGiven: two generating units with incremental heat rate (IHR) curves specifiedas three connected line segments (four points as shown in Figure 3.30).Unit 1:PointMWIHR (Btu/kWh)1007,0008,20020033008,900440011,000Fuel cost for unit 1=1.60$/MBtuUnit 2:PointMWIHR (Btu/kWh)75007700150275390450Fuel cost for unit 2=2.10$/MBtu381008500Both units are running. Calculate the optimum schedule (i.c., the unit megawattoutput for each unit) for various total megawatt values to be supplied by theunits. Find the schedule for these total megawatt values:300 MW. 500 MW. 700 MW, 840 MWNotes: Piecewise linear increment cost curves are quite common in digital com-puter executions of economic dispatch. The problem is best solved by using a"search" technique. In such a technique, the incremental cost is given a value andthe units are scheduled to meet this incremental cost. The megawatt outputs for theunits are added together and compared to the desired total. Depending on thedifference, and whether the resulting total is above or below the desired total, a newvalue of incremental cost is "tried." This is repeated until the incremental cost isfound that gives the correct desired value. Thc trick is to search in an efficientmanner so that the number of iterations is minimized.CS CamScanner - ó ä> guaall

Two generating units with increamental heart rate

3.2 Dispatch with Three-Segment Piecewise Linear Incremental Heat Rate Function Given: two generating units with incremental heat rate (IHR) curves specified as three connected line segments (four points as shown in Figure 3.30). Unit 1: Point MW IHR (Btu/kWh) 100 7,000 200 8,200 3 300 8,900 4 400 11,000 Fuel cost for unitI=1.60S/MBtu Unit 2: Point MW IHR (Btu/kWh) 150 275 390 450 Fuel cost for unit 2=2.10$/MBIU 7500 7700 3 8100 8500 4 Both units are running. Calculate the optimum schedule (i.c., the unit megawatt output for each unit) for various total megawatt values to be supplied by the units. Find the schedule for these total megawatt values: 300 MW. 500 MW. 700 MW, 840 MW

3.2 Dispatch with Three-Segment Piecewise Linear Incremental Heat Rate Function Given: two generating units with incremental heat rate (IHR) curves specified as three connected line segments (four points as shown in Figure 3.30). Unit 1: Point MW IHR (Btu/kWh) 100 7,000 200 8,200 3 300 8,900 4 400 11,000 Fuel cost for unitI=1.60S/MBtu Unit 2: Point MW IHR (Btu/kWh) 150 275 390 450 Fuel cost for unit 2=2.10$/MBIU 7500 7700 3 8100 8500 4 Both units are running. Calculate the optimum schedule (i.c., the unit megawatt output for each unit) for various total megawatt values to be supplied by the units. Find the schedule for these total megawatt values: 300 MW. 500 MW. 700 MW, 840 MW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.47P: Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of...

See similar textbooks

Similar questions

To convert a per-unit impedance from old to new base values, the equation to be used is Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)
Discuss the role of FACTS (Flexible Alternating Current Transmission Systems) devices in power system control and optimization.
What are FACTS (Flexible Alternating Current Transmission Systems), and how do they enhance power system performance and control?
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
Discuss the concept of reactive power and its role in grid stability.
What are FACTS (Flexible Alternating Current Transmission Systems) devices, and how do they enhance the control and stability of power systems?
please explain the operating principle of single phase 2S-2P PMSM based on 3D design illustration.
Explain the concept of FACTS (Flexible Alternating Current Transmission Systems) devices. How do they enhance the control and stability of power systems? Provide examples of FACTS devices and their applications.
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X12 = 0.2 p.u., X13 = X23 = 0. 1 p.u. The power flow in the system is given as: PF12 = 50 MW, PF13 = 150 MW, PF23 = 50 MW. Based on readings from 2 meters (not including M12 meter), M13 = 145 MW (not calibrated), and M23 = 50 MW (well calibrated), deduce the flow on line 1-2. Select one: O a. PF12 = - 47.5 MW. O b. None of these O c. PF12 = 67.5 MW. O d. PF12 = 47.5 MW. O e. PF12 =- 57.5 MW. O f. PF12 = 57 MW.
in distribution transformers; What is 30 degrees phase shift in delta-star connection? What are the disadvantages? (can you explain with drawing?)
please solve for nodal stress method. (if it is possible to apply supernodes)
What are FACTS (Flexible Alternating Current Transmission Systems) devices, and how do they enhance power system control?