3.. Assume the system in Figure 3 is underdamped and has a specification that by 2 seconds, the output must settle in to within 2% following a step change. Find the value of the pole, a, that will satisfy that requirement. Find the natural frequency wn. Find the damping ratio . a. b. C. R(S) Figure 3 sta s+2 Y(s)

3.. Assume the system in Figure 3 is underdamped and has a specification that by 2 seconds, the output must settle in to within 2% following a step change. Find the value of the pole, a, that will satisfy that requirement. Find the natural frequency wn. Find the damping ratio . a. b. C. R(S) Figure 3 sta s+2 Y(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
Date Pags 2) A sinusoidal alteznating voltage has value of 200V and 50 Hz It cEOSses an EoMo S. a fzequency of the zeso axi in a pasitive disection when t=0. Detezmine ņ the Aime when voltage fizst teaches the instan Zenemus value of 200 V and 2) the whe time when Valtage madei mum. after passing throag its positive ualu e eeashes the value Of 141.4V.
An A.C Bridge as shown in the figure is used to measure unknown inductance L1. in companion with capacitance What would be the quality factor if the frequency is 1500 Hz & the various parameter are as below- 120V
A high voltage engineer cascades having 6 stages Each in the circut . each stages capacitance is 15 nF and Input voltage to the circuit is 100kV at 100 Hz and the load current is 1mA. so this voltages not enough with one moudle . So How much moudle can be connect in cascades fashion .Justify your opinion with relevant mathematical analysis.
Consider a circuit with a pull-down resistor in parallel to a component. Compare a resistor with higher resistance value to a resistor with lower resistance value in the parallel path. Which resistor value will pull down the potential more, relative to ground, at the high side of the component? They will pull the potential di [ Select] They will pull the potential down equally, because resistors in series have equal voltage across them, regardless of resistance value. The lower-value resistor. There is not enough information to correctly answer this question. The higher-value resistor.
A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?
Draw the phasor diagram for both series and parallel RLC circuits in parts (i) and (ii). Discuss the effects of changing the capacitor connection in parallel on the power factor of the circuit.
V, = @sin(@t) + 2@ cos(@t). For this 6. A LRC circuit below is used to modify an input voltage applicatio, = 2 ydurāifidrentidi equation gnlist be in terms of %3D charge 9 notes to generate the general solution. No other method will be accepted. Use two decimal point accuracy. You . You must use the complimentary and particular solution method as shown in your are given that -2N@² + 20N = 2@ and -2M@² +20M = 2@¸ which you must use to simplify your particular solution when you equate coefficients. L HH Va VL Vc keo = Im sin(ot) Vs
4) The arms of a four an arm bridge a, b, c and d supplied with a sinusoidal voltage have the following values: -Arm ab: A resistance of 80092 in parallel with a capacitance of 2uF. -Arm bc: 400 resistance. -Arm cd: 1k0 resistance -Arm da: A resistance of R₂ in series with a capacitance of 2μF. Determine the value of R₂ and the frequency at which the bridge at balance.
. For the circuit shown in figure. The value of Zi is .................. kohm . * 82.86 104.86 84.86 92.86 99.86 108.86 The value of re is ..............ohm. . * 4.718 9.418 5.218 7.918 8.318 6.818 The value of Zi is .................. ohm . NOTE: use with CE in place (bypassed) * 720.67 630.67 650.67 640.67 710.67 680.67 The value of Av is .................. . NOTE: use with CE in place (bypassed) * -382.675 -272.675 -282.675 -362.675 -322.675 -392.675 The value of Av is .................. . * -1.805 -1.205 -1.105 -2.506 -2.405 -2.706 The…
Please show your detailed solution Number 15 A circuit with a resistor and capacitor in series takes 200 W at a power factor of 0.40 from 200-V 50-Hz supply. The capacitance of the circuit is A. 32?F C. 66.4?F B. 43.4 ?F D. 80?F
Describe the steady-state similarities and differences of DC and AC circuits with purelyresistive elements