3. What is the resulting factor of safety in a solid steel shaft, SAE1030 carbon steel, 2-7/8 inches in diameter and 5 feet in length that is supporting a direct tensile load of 60,000 lbs, stress concentration factor K=1.47 and the yield strength is 40,000 psi? a. 2.9 b. 4.5 C. 3.4 d. 5.3 4. A bolt is subjected to an axial shock loading and the supplied load equals 12 kN. Assuming allowable stress of 55 MPa, determine the size of the bolt required. Use a stress concentration factor of 1.8. a. 18.67mm b. 26.67mm

3. What is the resulting factor of safety in a solid steel shaft, SAE1030 carbon steel, 2-7/8 inches in diameter and 5 feet in length that is supporting a direct tensile load of 60,000 lbs, stress concentration factor K=1.47 and the yield strength is 40,000 psi? a. 2.9 b. 4.5 C. 3.4 d. 5.3 4. A bolt is subjected to an axial shock loading and the supplied load equals 12 kN. Assuming allowable stress of 55 MPa, determine the size of the bolt required. Use a stress concentration factor of 1.8. a. 18.67mm b. 26.67mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) A 6061-T6 aluminium alloy flat, simply supported disk valve of 0.2 m diameter and 10 mm thickness is subject to a water pressure of 0.5 MPa. What is the factor of safety, assuming failure to take place according to the maximum principal stress theory? The yield strength of the material is 241 MPa, E=200 GPa and v=0.3.
3.Shaft A, shown below, is made from AISI 1020 hot-rolled steel, welded to a fixed support, and is subjected to loading by equal and opposite forces F via shaft B. A theoretical stress-concentration factor Kts of 1.6 is induced by the 1/8" fillet. The length of shaft A from the fixed support to the connection at shaft B is 2 ft. The load F cycles from 150 to 500 lbf. (a) For shaft A, the factor of safety for infinite life using the Modified Goodman fatigue failure criterion is ( _) (b) For shaft A, the factor of safety for infinite life using the Gerber fatigue failure criterion is ( in fillet 2-in dia Shaft A 1 in 1 in Shaft B
The cylinder of a four stroke diesel engine has the followin, specifications : Cylinder bore :150 mm Maximum pressure : 3.5 MPa Cylinder material : GCI FG200 Factor of safety : 6 Poisson's ratio : 0.25 Determine the thickness of the cylinder wall. Also calculate the apparent and net circumferential stresses in the cylinder wall.
A single L8x6x1/2 (A36 steel) is used as a tension brace in a multi-story building. The 8 inch leg of the angle is attached to a gusset plate with two lines of four ¾ inch Ø bolts at a spacing of 3 inches. Determine the shear lag factor (consider Case 2 & 8) and the effective net area. Considering yielding and net section rupture, determine the design strength by LRFD and the allowable strength by ASD. (PLEASE SOLVE THIS ONE WITH THE BOLD TEXT)
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
Q2: A cold drawn steel rod of circular cross- section is subjected to a variable bending moment of 565 N.m to 1130 N-m as the axial load varies from 4500 N to 13 500 N. Determine the required diameter of the rod for a factor of safety 2. Neglect any stress concentration and column effect. Assume the following values: Ultimate strength = 550 MPa %3D Yield strength = 470 MPa Size factor = 0.85 Surface finish factor = 0.89 Correction factors = 1.0 for bending = 0.7 for axial %3D load The endurance limit in reversed bending may be taken as one-half the ultimate strength.
(14) A 40mm steel shaft rotates @ 600rpm & handles 10kW delivered from a pulley located 300mm from one side of the bearing. The shaft is supported by bearing 800mm apart. Assume that force acting on the shaft is the equal to the maximum belt pull. Determine the maximum combined stress of the shaft. (15) A 150mm pulley is mounted to the motor 100mm from the bearing. The motor is 20kW & rotates @ 640rpm. The belt wraps the pulley @ 170°. The net belt tension is acting as transverse load on the shaft. Determine the combine stress on the shaft.
Q 4 A spherical tank for storing gas under pressure is 25 m in diameter and is made of structural steel 15 mm thick.The yield point of the material is 250 MPa and a safety factor of 2.5 is adequate. Determine the maximum permissible internal pressure.[ assuming the welded seams between the various plates are as strong as the solid metal]
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14
3) A flange coupling is to connect two 60mm shafts. The hubs of the coupling are 120mm, 100mm thick, & the flange webs are 20 mm thick. Six M16 bolts fasten the flange from a 165 bolt circle. The keyway is 15mm shorter than the hub’s thickness & the key is 15mm x 15mm. The coupling transmits 45kW @ 450rpm. The yield point in shear for all materials is half of its yield point in tension or compression. Yield tensile strength is 0.75 of ultimate strength of the materials. The Sult is 448N/mm2 . Find: (a) the shear stress in key; (b) the bearing stress in key; (c) the shear stress in bolts; (d) bearing stress in flange.
A shaft made of 40 C 8 steel is used to drive a machine. It rotates at 1500 r.p.m. The pulleys A, B and the bearings C, D are located as shown in Fig. 14.21. The belt tensions are also shown in the figure. Determine the diameter of the shaft. The permissible shear stress for the shaft material is 100 MPa.The combined shock and fatigue factor applied to bending and torsion are 1.5 and 1.2 respectively.
A solid cylindrical shaft made of AISI 1020 steel(quenched and tempered at 870oC) rotates at a speedthat produces a safety factor of 2.5 against the stresscausing yielding. To instrument the shaft, a small hole isdrilled in its center for electric wires. At the same timethe material is changed to AISI 1080 steel that has beenquenched and tempered at 800oC. Find the safety factoragainst yielding of the new shaft.