3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is a cantilever beam carrying a uniformly distributed load of 4 KN/m freely supported on beam AB. Beam AB is freely supported on each ends. E = 13.8 GPa for both beam. Neglect the weight of the beam. a. Compute the reaction at D. b. Compute the deflection at D. c. Compute the bending stress of beam CD. 4kN Im 4m 4m

3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is a cantilever beam carrying a uniformly distributed load of 4 KN/m freely supported on beam AB. Beam AB is freely supported on each ends. E = 13.8 GPa for both beam. Neglect the weight of the beam. a. Compute the reaction at D. b. Compute the deflection at D. c. Compute the bending stress of beam CD. 4kN Im 4m 4m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

EXAMPLE 4.2 The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm²; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm?. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. %3D 0.4 m 0.3 m 30 kN D E -0.4 m 0.2 m
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm^2; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm^2. For the 30 kN force shown, determine the deflection of B and E, respectively. 0.4 m 0.3 m B A 0.2 m OC -0.4 m 30 kN E
The beam shown in the Fig.is 7m long with EI = 200MNm^2 Let P = 10 kN Determine the following: a. Reaction at A.b. Constant.c. Slope at 2m from A.d. Deflection at 2m from A.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm; link CD is-made of steet E = 200 GPa) and has a cross-sectional area 600 mm. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. 0.4 m 0.3 m 30 kN E T0.4 m 0.2 m
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Figure Q2(a) shows a cantilever beam that is subjected to a pure bending moment M = 3kN.m about the neutral axis (N.A) and the cross-section of a beam is shown in Figure Q2(b). Determine: (a) The moment of inertia about the neutral axis, InA. (b) The bending stress acting at point B and state whether it is in tension or compression. (c) The bending stress acting at point C (d) The maximum bending stress in the beam. M Figure Q2 (a) 20 mm B 150 mm C N 20 mm 150 mm 20 mm 250 mm Figure Q2 (b)
Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 17 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 105°F. Use the following dimensions and properties: a = 3.0 ft, b = 5.5 ft. Rod (1): di = 0.90 in., L1 13 ft, Ej = 15,200 ksi, a1 12.20 x 10-6"F. Rod (2): d2 = 0.70 in., L2 10 ft, E2 = 28,000 ksi, a2 = 9.60 x 10-6"F. Rod (3): d3 1.20 in., L3 = 6 ft, E3 = 15,200 ksi, a= 12.20 × 10-6ľF. |(1) (2) b |L2 a Rigid bar A |(3) L3 D
A cantilever beam is 4m long with a EI = 20MNm^2. It has a point load of P=1kN at the free end and a u.d.l of q = 300N/m along its entire length. what is the reaction at A? what is the moment at A? Calculate the following at the free end slope and deflection
Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 24 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 115 Fo. Use the following dimensions and properties: a = 3.5 ft, b = 7.5 ft. Rod (1): d 1= 1.10 in.,L 1= 12 ft , E 1= 15,200 ksi , a 1= 12.20 × 10 - 6 /Fo. Rod (2): d 2 = 0.65 in. , L 2 = 10 ft , E 2 = 28,000 ksi, a 2 = 9.60 x 10 - 6/Fo. Rod (3): d 3 = 1.15 in. , L 3 = 6 ft, E3 = 15,200 ksi , a 3 = 12.20 x 10 - 6/Fo. (1) L (2) b L2 a Rigid bar A (3) L3 vD = i in.
A rigid beam BC is suspended by rods AB and CD as shown in the figure. Rod AB is made in from aluminum while rod CD is made from steel. Determine the location/placement of the 75kN concentrated load within the beam BC such that the rigid beam BC will remain horizontal after deflection. Determine the axial deformation of rods AB and CD.
Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 16 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 125°F. Use the following dimensions and properties: a = 2.8 ft, b = 6.3 ft. Rod (1): d₁ = 0.90 in., L₁ = 11 ft, E₁ = 15,200 ksi, α₁ = 12.20 × 10-6/°F. Rod (2): d₂ = 0.80 in., L₂ = 9 ft, E2 = 28,000 ksi, a₂ = 9.60 × 10-6/F. Rod (3): d3 = 1.25 in., L3 = 5 ft, E3 = 15,200 ksi, a3 = 12.20 x 10-6/°F. VD = i L in. (1) A a L3 B (3) D b Rigid bar L2
Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 22 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 70°F. Use the following dimensions and properties: a = 3.5 ft, b = 7.3 ft. Rod (1): d₁1.10 in., L₁ = 13ft, E₁ = 15,200 ksi, a₁ = 12.20 x 10-6/°F. Rod (2): d₂ = 0.70 in., L₂ = 9ft, E₂ = 28,000 ksi, %₂ = 9.60 x 10-6/°F. = 6ft, E3 = 15,200 ksi, a3 = 12.20 x 10-6/°F. Rod (3): d = 1.15 in., L VD = i (1) (2) a b H Rigid bar B (3) L3 OD L in. N P L₂