3. The daily streamflow data of a river for a drainage area of 5,810 km' are given in table below. Determine the equivalent depth of the direct runoff by separating the baseflow. (Use recession curve method-N-0.8A) Time (days). Flow (m'/s) 1,600 1,550 5,000 11,300 8,600 6,500 5,000 3,800 Time (days). 9. 10 Flow (m/s) 2,800 2,200 1,850 1,600 1.330 1.300 1,280 3. 11 12 13 4. 6. 7. 14 15

3. The daily streamflow data of a river for a drainage area of 5,810 km' are given in table below. Determine the equivalent depth of the direct runoff by separating the baseflow. (Use recession curve method-N-0.8A) Time (days). Flow (m'/s) 1,600 1,550 5,000 11,300 8,600 6,500 5,000 3,800 Time (days). 9. 10 Flow (m/s) 2,800 2,200 1,850 1,600 1.330 1.300 1,280 3. 11 12 13 4. 6. 7. 14 15

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) The equation for finding the water head in an open channel flow is given below. is given. In this equation, the channel width (B=8 units) and the flow rate of the water in the channel (Q=5 units) Since the height of the water in the channel is estimated to be between x1-0 and x2=2 units, What is the actual height (H) of the water in the channel? (You can make your transactions less than 0.05% of the approximate error.) continue until it is lower than and take six digits after the comma) 0.471405 x ( BH)5/% f(H) = %3D (B + 2 x H)2/3
Cross section of a wadi at a catchment outlet is shown in the given figure. It is required to obtain variation of wadi-flow rates (hydrograph) during rainfall events. If you were assigned to install a wadi-gage station there, clearly explain the measurements need to be taken and procedure to be followed to develop the rating curve.
I have tried by assuming Vdot value, Put value in 4equation that I got, 1. Flow rate equation 2. Reynold number equation 3. Haaland's equation 4. H(available) = H(required) I tried to solve it by iteration, However, I can't figure out, which value I could use with the iteration technique
From the below given graph for venturimeter experiment ,the value of A is 4.85 and the value of B is 4.1 the value of C is 3.98 , the value of D is 6 „Then coefficient of discharge (Cd) value is calculated as у-аxis From the graph take slope find out Ca B- D Q theoretical Qactual
MT NUIES ASK YOUR (a) Find a conversion factor to convert from miles per hour to kilometers por hour, mi/h x = km/h (b) Suppose the maximum highway speed is 70 mi/h, Use the conversion factor from part (a) to find the speed in kilometers per hour. km/h (c) Suppose the maximum highway speed has been raised to B5 mi/h in some places. In kilometers per hour, how much of an increase is this over the 70 mi/h limit? km/h
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
Water is flowing at a depth of 10.0 ft with a velocity of 10.0 ft/s in a channel of rectangular section. a)If there is a smooth contraction in the channel width from 10.0 ft to 9.0 ft, calculate the flow depth in feet in the contracted section using a solver. b)If there is a smooth contraction in width from original upstream width of 10.0 feet, find the minimum width (in feet) in the contraction so that choking is prevented.
Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,
water at ambient temperature flows through a horizontal tube (surface roughness 0.15mm) of diameter (10 square root 8 mm) with a pressure drop (pressure gradient) of (1000 square root 8) n/m3. Calculate using trial and error method (use at least four digits in your calculations). a) the friction factor, b) the average velocity c) the volumetric flow rate d) the mass flow rate e) the Reynolds number. Characterize the flow.
For the conduction of the water there is a height difference of 38 m. The results obtained from the hydraulic calculation for three different diameters are shown in the following table Diameter, in. Total head loss, mca 8 56.5 12 37.2 16 29.1 What will be the available driving load? TRANSLATED FROM Para la conducción del agua se cuenta con un desnivel de cotas de 38 m. Los resultados obtenidos del cálculo hidráulico para tres diámetros diferentes son mostrados en la siguiente tabla: Diámetro, plgs. Pérdida de carga total, mca 8 56.5 12 37.2 16 29.1 ¿Cuál será la carga de conducción disponible?
A concrete-lined channel is used to convey water flow between Point A at surface elevation of 510 m and point B at surface elevation of 508 m above sea level over a distance of 2 kilometers. The surface roughness coefficient of the concrete is 0.012. The flow conveyed by this channel in m³/s is most nearly: A. 70 B. 105 C. 150 D. 165 4m 5 m 4m
In a 250 mm diameter pipe, oil discharges through a sharp crested round orifice, 100 mm in diameter. If the coefficient of contraction (Cc) and coefficient of velocity (Cv) are 0.63 and 0.98, respectively. SG of oil is 0.86. Determine the following: a) discharge from the orifice, (L/s) given that: coefficient of orifice, Co= Cc x Cv b) diameter of jet (mm) given that: Cc = Ajet/Atheo c) actual velocity in the jet, (ft/s) Note: Maintain 3 decimal places on partial and final answers.